Infinity 6100m Instructions Manual Download Page 8

Infinity Systems, 250 Crossways Park Drive, Woodbury, NY 11797 USA 
516.674.4INF (4463) • FAX 516.682.3556 • www.infinitysystems.com
© 2005 Harman International Industries, Incorporated. All rights reserved.
Infinity, Harman International and CMMD are trademarks, of Harman International 
Industries, Incorporated, registered in the United States and/or other countries.
CMMD patent nos. 6,327,372 and 6,404,897.
Part No. 6100MOM11/05

• PROBLEM:

No audio (blue LED off, red LED flashing).**

CAUSE and SOLUTION:
1. Thermal  protection.

– Turn the system off and allow the amplifier

to cool off. 

• PROBLEM:

Distorted audio (blue LED on, red LED off). 

CAUSES and SOLUTIONS:
1. Gain control is set too high, or amplifier or

source unit is defective. 
– Check gain setting.
– Source unit output is distorted.

2. Short circuit in speaker wires.

– Check speaker wires for shorts or grounds.

• PROBLEM:

Music lacks punch. 

CAUSE and SOLUTION:
1. Speakers are not connected properly. 

– Check speaker connections for proper

polarity.

• PROBLEM:

No audio from page. 

CAUSES and SOLUTIONS:
1. Microphone is not connected properly.

– Check microphone connections.

2. Page level set to minimum.

– Check level control on microphone.

S

PECIFICATIONS

6100m

• 125W x 2 ch. 

• Frequency Response: 10Hz – 40kHz

• Signal-to-Noise Ratio: 91dB

• Line-Level Input Sensitivity: 250mV – 6V

• Speaker-Level Input Sensitivity: 6V – 16V

• Speakers: 11" x 18" x 14-1/2"

• Amplifier: 8-1/8" x 8" x 2-3/8"

• Microphone: 1-1/4" x 2-1/2" x 3-5/8"

• Min. Speaker Impedance: 4 ohms, stereo

6000m

• Power Handling: 150W

• Peak Power Handling: 450W

• Sensitivity: 93dB @ 2.83V

• Frequency Response: 80Hz – 20kHz

• Impedance: 4 ohms

• Polypropylene Cone

• Cast-Polymer Basket

• CMMD

Tweeter

• Rubber Surrounds

• UV-Resistant

• Water-Resistant

• Salt-Spray-Resistant

• 11" x 18" x 14-1/2"

2100m

• 125W x 2 ch. @ 4 ohms

• 150W x 2 ch. @ 2 ohms

• 250W x 1 ch. @ 4 ohms

• Frequency Response: 10Hz – 40kHz

• Signal-to-Noise Ratio: 91dB

• Line-Level Input Sensitivity: 250mV – 6V

• Speaker-Level Input Sensitivity: 6V – 16V

• 8-1/8" x 8" x 2-3/8"

• Min. Speaker Impedance: 2 ohms, stereo

4 ohms, bridged

• PROBLEM:

Page is distorted.

CAUSES and SOLUTIONS:
1. Page level is too high. 

– Reduce page level.

2. Shouting into microphone. 

– Hold microphone away from face.

• PROBLEM:

Feedback.

CAUSES and SOLUTIONS:
1. Squealing sound from the speakers when

using the Paging system. 
– Reduce page level on microphone.
– Increase distance between microphone 

and mouth while speaking.

Features, specifications and appearance are subject to change without notice.

• PROBLEM:

No audio (POWER LEDs are off). 

CAUSES and SOLUTIONS:
1. No voltage at Batt + or remote terminal. 

– Check all power connections with a VOM.

2. Poor ground connection. 

– Check fuses.

3. Microphone power switch is off. 

– Check power switch on Mic.

• PROBLEM:

No audio (POWER LEDs are on). 

CAUSE and SOLUTIONS:
1. No input signal or no speaker signal.

– Check all input connections from source unit.
– Check all speaker connections.
– Check fader control on head unit.

• PROBLEM:

No audio (blue LED on – red LED flashing).**

CAUSES and SOLUTIONS:
1. Over or under voltage. 

– Battery voltage above 16 volts or below 

10 volts. Check battery and charging system
for proper operation. 

2. Shorted output. 

– Check speaker connections and wires.

** 

NOTE:

The microphone has a blue power LED

and the amplifier has a red power LED.

T

ROUBLESHOOTING

Declaration of Conformity

We, Harman Consumer Group International

2, route de Tours 
72500 Château-du-Loir
France

declare in own responsibility that the products described in this owner’s
manual are in compliance with technical standards: 

EN 61000-6-3:2001
EN 61000-6-1:2001

Klaus Lebherz

Harman Consumer Group International

Château-du-Loir, France  11/05

Declaration of Conformity

We, Harman Consumer Group International

2, route de Tours 
72500 Château-du-Loir
France

declare in own responsibility that the products described in this owner’s
manual are in compliance with technical standards: 

EN 55013:2001+A1:2003
EN 55020:2002+A1:2003

Klaus Lebherz

Harman Consumer Group International

Château-du-Loir, France  11/05

Summary of Contents for 6100m









Reviews: