Infineon TRAVEO T2G family CYT4D Series Manual Download Page 23

Page: 23 / 80

Application Note

23 of 80

002-26071 Rev. *B

2021-09-07

Clock configuration setup in TRAVEO™ T2G family CYT4D series MCUs

Configuration of the clock resources

3.5

Setting the LPECO

The LPCEO is disabled by default. The LPECO cannot be used unless it is enabled.

Figure 11

shows how to

configure registers for enabling the LPECO. To disable the LPECO, write

‘

’

to the LPECO_EN bit of the

BACKUP_LPECO_CTL register.

Start

End(Success)

LPECO_STATUS is ready?

Enable LPECO

Yes

Configure value to BACKUP_LPECO_CTL

Specifies the load capacitance of the chosen crystal, the

crystal frequency range, and the oscillation amplitude

selection

(1)

(3)

Wait until LPECO is available

(2)

Figure 11

LPECO configuration

3.5.1

Use case

•

Oscillator to use: Crystal unit

•

Fundamental frequency: 8 MHz

Note:

These values are decided in consultation with the crystal unit vendor.

Table 5

lists the parameters and

Table 6

lists the functions of the configuration part of in the SDL for LPECO

settings.

Table 5

List of LPECO settings parameters

Parameters

Description

Value

WAIT_FOR_STABILIZATION

Waiting for stabilization

10000ul

CLK_FREQ_LPECO

Source clock frequency

8000000ul

CY_SYSCLK_BAK_LPECO_LCAP_
5TO10PF

Backup domain LPECO load is in the range of
5 pF to 10 pF.

0ul

CY_SYSCLK_BAK_LPECO_FREQ_
6TO8MHZ

Backup domain LPECO frequency is in the
range of 6 MHz to 8 MHz.

1ul

CY_SYSCLK_BAK_LPECO_AMP_
MAX_1P35V

Backup domain LPECO maximum oscillation
amplitude is 1.35 V.

0ul

Summary of Contents for TRAVEO T2G family CYT4D Series

















































































Search results

Summary of Contents for TRAVEO T2G family CYT4D Series

Reviews:

Related manuals for TRAVEO T2G family CYT4D Series

Brands by name

Popular brands

Infineon TRAVEO T2G family CYT4D Series, Manual

Search results

Summary of Contents for TRAVEO T2G family CYT4D Series

Reviews:

Related manuals for TRAVEO T2G family CYT4D Series

Brands by name

Popular brands