background image

 

 

 

Trademarks  

All referenced product or service names and trademarks are the property of their respective owners. 

 

 

 

Edition 2020-11-12 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

 

 

 

 

 

 

 

 
Published by 
Infineon Technologies AG 
81726 Munich, Germany 
 
© 2020 Infineon Technologies AG. 
All Rights Reserved. 

 
Do you have a question about this 
document? 
Email: 

[email protected]

 

 
Document reference  

IMPORTANT NOTICE 

The information contained in this application note 

is  given  as  a  hint  for  the  implementation  of  the 

product only and shall in no event be regarded as a 

description  or  warranty  of  a  certain  functionality, 

condition  or  quality  of  the  product.  Before 

implementation of the product, the recipient of this 

application note must verify any function and other 

technical  information  given  herein  in  the  real 

application. 

Infineon 

Technologies 

hereby 

disclaims  any  and  all  warranties  and  liabilities  of 

any kind (including without limitation warranties of 

non-infringement  of  intellectual  property  rights  of 

any  third  party)  with  respect  to  any  and  all 

information given in this application note.  

 

The data contained in this document is exclusively 

intended  for  technically  trained  staff.  It  is  the 

responsibility of customer’s technical departments 

to  evaluate  the  suitability  of  the  product  for  the 

intended  application  and  the  completeness  of  the 

product  information  given  in  this  document  with 

respect to such application.     

 

 

For further information on the product, technology, 

delivery  terms  and  conditions  and  prices  please 

contact  your  nearest  Infineon  Technologies  office 

(

www.infineon.com

). 

 
WARNINGS 

Due  to  technical  requirements  products  may 

contain  dangerous  substances.  For information  on 

the  types  in  question  please  contact  your  nearest 

Infineon Technologies office. 

 

Except as otherwise explicitly approved by Infineon 

Technologies  in  a  written  document  signed  by 

authorized 

representatives 

of 

Infineon 

Technologies, Infineon Technologies’ products may 

not  be  used  in  any  applications  where  a  failure  of 

the product or any consequences of the use thereof 

can  reasonably  be  expected  to  result  in  personal 

injury. 

 

 

 

 

 

 

Summary of Contents for PG-LQFP





















Reviews: