background image

  

 

User Guide 

3 of 25 

002-34554 Rev. *A  

 

 

2022-08-01 

CY-SD4210 EZ-

USB™ SX3 HDMI 4K capture

 kit guide 

 
 

Introduction 

 

1

 

Introduction

 

The CY-SD4210 EZ-

USB™ SX3 HDMI 4K capture solution demo kit is based on the SX3 product family of 

Infineon’s configurable SuperSpeed USB controllers. 

 

SX3 has a fully configurable general interface that can interface with any processor, ASIC, image sensor, or 
FPGA. It provides easy and effortless connectivity to popular industry interfaces such as synchronous slave FIFO 
and image sensor interfaces. The EZ-

USB™ SX3 HDMI 4K capture kit combines hard

ware, software and 

documentation that enable customers to stream video from an HDMI source directly into a PC. This user guide 
describes the steps to install the software required by the SX3 HDMI 4K capture kit and to operate the 
development board provided with the kit.  

This kit is intended to be a solution demo kit for USB Type C audio and video streaming applications from an 
HDMI source.  

See the device datasheet

[4]

 to understand and compare the various features supported by EZ-USB

 SX3 

controllers. 

The CY-SD4210 EZ-

USB™ SX3 HDMI 4K capture solution demo kit supports the following key features:

 

 

Audio and video streaming up to 4K (UHD) at 30 fps from an HDMI source 

 

USB bus-powered operation 

 

Onboard regulators 

To view the SX3 controller details, see the 

webpage

.  

1.1

 

Kit contents

 

The CY-SD4210 EZ-

USB™ SX3 HDMI 4K capture solution demo kit consists of the following:

 

Table 1

 

Kit contents 

Item 

Type 

Comments 

SX3 HDMI 4K capture kit 

Hardware 

SuperSpeed USB-C cable 

Cable 

HDMI-A male cable 

Cable 

Hard copy of the quick-start 
guide (QSG) 

Documentation  - 

Mechanical enclosure 

Enclosure 

Kit casing 

Package 

Foam 

Package 

To protect and maintain proper placement in the kit 
container 

1.2

 

Downloading kit documents and hardware design files

 

The documents and the hardware design files for CY-SD4210 EZ-

USB™ SX3 

HDMI 4K capture kit can be 

downloaded from the kit webpag

[3]

The documents include a QSG, kit user guide (this document), and 

release notes. The hardware design files include schematic, bill of materials (BOM), and layout files.  

1.3

 

Board details

 

This section lists the key interfaces of the CY-SD4210 board.  

Summary of Contents for CY-SD4210


























Reviews: