Infineon BTN7030-1EPA User Manual Download Page 16

 

 

 

Trademarks of Infineon Technologies AG 

All referenced product or service names and trademarks are the property of their respective owners. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

owners. 

Edition 2020-01-21 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

 

 

 

 

 
Published by 
Infineon Technologies AG 
81726 Munich, Germany 
 
© 2021 Infineon Technologies AG. 
All Rights Reserved. 

 
Do you have a question about this 
document? 
Email: 

[email protected] 

 
Document reference  

IMPORTANT NOTICE 

The information contained in this application note is 

given as a hint for the implementation of the product 

only  and  shall  in  no  event  be  regarded  as  a 

description  or  warranty  of  a  certain  functionality, 

condition  or  quality  of  the  product.  Before 

implementation of the product, the recipient of this 

application note must verify any function and other 

technical  information  given  herein  in  the  real 

application. Infineon Technologies hereby disclaims 

any  and  all  warranties  and  liabilities  of  any  kind 

(including  without  limitation  warranties  of  non-

infringement  of  intellectual  property  rights  of  any 

third party) with respect to any and all information 

given in this application note.  

 

The data contained in this document is exclusively 

intended  for  technically  trained  staff.  It  is  the 

responsibility of customer’s technical departments 

to  evaluate  the  suitability  of  the  product  for  the 

intended  application  and  the  completeness  of  the 

product  information  given  in  this  document  with 

respect to such application.     

 

 

For further information on the product, technology, 

delivery  terms  and  conditions  and  prices  please 

contact  your  nearest  Infineon  Technologies  office 

(

www.infineon.com

). 

 
WARNINGS 

Due to technical requirements products may contain 

dangerous substances. For information on the types 

in  question  please  contact  your  nearest  Infineon 

Technologies office. 

 

Except as otherwise explicitly approved by Infineon 

Technologies  in  a  written  document  signed  by 

authorized 

representatives 

of 

Infineon 

Technologies, Infineon Technologies’ products may 

not be used in any applications where a failure of the 

product or any consequences of the use thereof can 

reasonably be expected to result in personal injury. 

 

 

 

 

 

 

 

Summary of Contents for BTN7030-1EPA

















Reviews: