manualshive.com logo in svg

Infineon Technologies XC2200, User Manual

Share
Download
Infineon Technologies XC2200 User Manual Download Page 64

XC2200 Derivatives

System Units (Vol. 1 of 2)

Memory Organization

 

User’s Manual

3-3

V2.1, 2008-08

MemoryX2K, V1.3

 

3.1

Address Mapping

All the various memory areas and peripheral registers (see 

Table 3-1

) are mapped into

one contiguous address space. All sections can be accessed in the same way. The
memory map of the XC2200 contains some reserved areas, so future derivatives can be
enhanced in an upward-compatible fashion.

Note:

Table 3-1

 shows the maximum available memory areas. The actual available

memory areas depend on the selected device type.

Table 3-1

XC2200 Memory Map

1)

Address Area

Start Loc. End Loc. Area Size

2)

Notes

IMB register space

FF’FF00

H

FF’FFFF

H

256 Bytes

Reserved (access trap)

F0’0000

H

FF’FEFF

H

< 1 MByte

Minus IMB registers

Reserved for EPSRAM

E9’0000

H

EF’FFFF

H

448 KBytes

Mirrors EPSRAM

Emulated PSRAM

E8’0000

H

E8’FFFF

H

64 KBytes

With Flash timing

Reserved for PSRAM

E1’0000

H

E7’FFFF

H

448 KBytes

Mirrors PSRAM

PSRAM

E0’0000

H

E0’FFFF

H

64 KBytes

Program SRAM

Reserved for Flash

CC’0000

H

DF’FFFF

H

<1.25 MBytes

Flash 2

C8’0000

H

CB’FFFF

H

256 KBytes

Flash 1

C4’0000

H

C7’FFFF

H

256 KBytes

Flash 0

C0’0000

H

C3’FFFF

H

252 KBytes

3)

Minus res. seg.

External memory area

40’0000

H

BF’FFFF

H

8 MBytes

External IO area

4)

20’5800

H

3F’FFFF

H

< 2 MBytes

Minus CAN/USIC

USIC registers

20’4000

H

20’57FF

H

6 KBytes

Accessed via EBC

MultiCAN registers

20’0000

H

20’3FFF

H

16 KBytes

Accessed via EBC

External memory area

01’0000

H

1F’FFFF

H

< 2 MBytes

Minus segment 0

SFR area

00’FE00

H

00’FFFF

H

0.5 KBytes

Dualport RAM (DPRAM) 00’F600

H

00’FDFF

H

2 KBytes

Reserved for DPRAM

00’F200

H

00’F5FF

H

1 KBytes

ESFR area

00’F000

H

00’F1FF

H

0.5 KBytes

XSFR area

00’E000

H

00’EFFF

H

4 KBytes

Data SRAM (DSRAM)

00’A000

H

00’DFFF

H

16 KBytes

Reserved for DSRAM

00’8000

H

00’9FFF

H

8 KBytes

External memory area

00’0000

H

00’7FFF

H

32 KBytes

Summary of Contents for XC2200






































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands