manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

Share
Download
Infineon Technologies TC1796 User Manual Download Page 924

TC1796

System Units (Vol. 1 of 2)

System Timer

 

User’s Manual

15-7

V2.0, 2007-07

STM, V2.0

 

The compare match interrupt flags STM_ICR.CMPxIR are immediately set after an STM
reset operation, caused by a compare match event with the reset values of the STM and
the compare registers STM_CMPx. This setting of the CMPxIR flags does not directly
generate compare match interrupts because the compare match interrupts are
automatically disabled after an STM reset (CMPxEN = 0). Therefore, before enabling a
compare match interrupt after an STM reset, the CMPxIR flags should be cleared by
software (writing register STM_ISSR with CMPxIRR set). Otherwise, undesired compare
match interrupt events are triggered accidentally.

15.3

Kernel Registers

This section describes the kernel registers of the STM. The STM registers can be divided
into four types, as shown in 

Figure 15-4

.

Note: In the TC1796, all kernel registers are readable in suspend mode.

STM Registers Overview

Figure 15-4 STM Registers 

The complete and detailed address map of the STM module with its registers is shown
in 

Table 18-5

 on 

Page 18-13

.

Table 15-2

Registers Address Space

Module

Base Address

End Address

Note

STM

F000 0200

H

F000 02FF

H

-

MCA05749_mod

STM_TIM0

Timer/Capture

Registers

STM_TIM1
STM_TIM2
STM_TIM3
STM_TIM4
STM_TIM5
STM_TIM6
STM_CAP

Compare 

Registers

STM_CMP0
STM_CMP1

Interrupt 

Registers

STM_ICR
STM_ISRR

STM_CMCON

General Module 

Registers

STM_CLC

STM_SRC0
STM_SRC1

STM_ID

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands