Infineon Technologies TC1796 User Manual Download | Manualshive

Page: 1551 / 2150

background image

TC1796

Peripheral Units (Vol. 2 of 2)

Micro Link Interface (MLI)

User’s Manual

23-42

V2.0, 2007-07

MLI, V2.0

23.2.2

General MLI Features

The general MLI features comprise the:
•

Parity generation and checking (see

)

•

Non-Acknowledge error (see

•

Address prediction (see

•

Automatic data transfers (see

•

Access protection (see

)

•

Transmit priority (see

)

•

Transmission delay (see

23.2.2.1 Parity Check and Parity Error Indication

For parity generation, the number of transmitted bits with the value of 1 is counted over
the header and the complete data field of a frame. For even parity, the parity bit is set if
the result of a modulo-2 division of the elaborated number is 1. For odd parity, the parity
bit is set if the result of a modulo-2 division of the elaborated number is 0.
For a parity error-free MLI connection, even parity must be selected in the transmitter
because the receiver operates only with even parity detection. The capability to select
odd parity can be used by the transmitter to force a parity error reply from the receiver
during the startup procedure of the MLI connection. This can be used to measure the
propagation delay and to optimize the ready delay time (see

Note: There is no protection against frames where more than one bit is corrupted (e.g.

shortened frames). In such a case, an unpredicted behavior of the MLI module
may occur.

Transmitting Controller

The MLI transmitter counts the detected parity error conditions and generates a parity
error event if a programmable number (max. 16) of parity error conditions has occurred.
A parity error condition is indicated to the transmitter by the receiver after the
transmission of a frame (see

). The transmitter parity error condition is

detected when the TREADY signal is sampled at low level within a programmable
number (TCR.MDP = maximum delay for parity errors) of TCLK clock cycles after
TVALID has been de-asserted to low.
If a transmitter parity error condition is detected, the MLI transmitter sets the parity error
flag TSTATR.PE and also decreases the maximum parity error counter TCR.MPE by 1.
The maximum parity error counter of the transmitter TCR.MPE determines the number
of transmit parity error conditions that can be still detected until a transmitter parity error
event is generated. If a transmitter parity error condition is detected and TCR.MPE is
becoming 0 or while it is 0, a transmitter parity error event is generated by setting bit
TISR.PEI (see

Figure 23-39

) and an SRx output line is activated if

enabled by TIER.PEIE = 1. After a transmitter parity error event occurred, TCR.MPE can

«
...
1549
1550
1551
1552
1553
...
»

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

Brand: Saitek Pages: 4

Brand: Kathrein Pages: 16

Brand: Samson Pages: 8

Brand: Samson Pages: 60

Brand: Samson Pages: 40

IntelliZone2 MasterStat

Brand: Water Furnace Pages: 44

U1000 iQpump Drive

Brand: YASKAWA Pages: 426

Brand: YASKAWA Pages: 26

Brand: YASKAWA Pages: 210

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 400

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 466

Brand: Newport Pages: 417

Brand: Dantel Pages: 6

GAMMA VERSUS Series

Brand: JCM Pages: 111

767-4804/000-800

Brand: WAGO Pages: 80

Brand: DeLaval Pages: 102

CIATControl OPC Server

Brand: CIAT Pages: 32

Brand: Danfoss Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands