Inficon UL5000 Technical Handbook Download Page 74

Page: 74 / 108

Description of the Menu

iina

e 0

chn

ica

l ha

boo

6.7

Information

•

The

enables submenus to select different kinds of

information belonging to the UL5000.

6.7.1

Service

•

Main Menu

Information

Service

This screen allows to get into the service menu. Enter the password first. The initial
service password is

not

provided with the shipment, only after a specific service

training. Please refer to Chapter

4.2.2.7

for the description of the entry.

The service menu appears after the successful input of the password. Special
functions (e. g. switching the valves manually) are possible in this menu only.
For further information please refer to Service Menu (iipa74e1-b).

Fig. 6-12: The

Information

Softkey 2:

View settings

The current settings will be displayed on 4 pages, e.g. trigger levels, test leak
mass, date and time.

Softkey 3:

View internal data

Information on measured internal data is provided on 4 screens.

Softkey 4:

Vacuum diagram

The vacuum diagram of the UL5000 will be displayed. Opened and closed
valves are also shown.

Softkey 5:

View error list

The list of occurred errors and warnings will be displayed.

Softkey 6:

Calibration history

The carried out calibrations will be listed.

Softkey 7:

Calibration factors

The vacuum diagram of the UL5000 is shown. Here you can see which
valves are opend or closed momentarily and more.

Softkey 8:

Service

(See Chapter

6.7.1

)

Summary of Contents for UL5000













































































































Search results

Summary of Contents for UL5000

Reviews:

Related manuals for UL5000

Brands by name

Popular brands

Inficon UL5000, Technical Handbook

Search results

Summary of Contents for UL5000

Reviews:

Related manuals for UL5000

Brands by name

Popular brands