Inficon Sensistor Sentrac Service Instructions Manual Download Page 54

Page: 54 / 76

5 | Service Instructions

INFICON

54 / 76

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

5.16 Changing Probe P60 LED Lamps

Part

Part no.

Qty

Consumables

KB1028 Wihite LED

591-801

LOCTITE

406

Disassemble

Disconnect the Probe from the Sensistor Sentrac.

Open the Probe Cover, see Disassemble in Open Probe P60 Cover [

}

49].

Remove the LED Lamps connector from the PCB (B).

Remove the LED Lamps (A). Carefully tap them out of their sockets.

Assemble

Install the new LED Lamps. Use Loctite 406 when attaching the lamps.

Reinstall all cables on the LED Lamps.

Reinstall the Probe Cover, see Assemble in Open Probe P60 Cover [

}

49].

Summary of Contents for Sensistor Sentrac













































































Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands

Inficon Sensistor Sentrac, Service Instructions Manual

Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands