Inficon Sensistor Sentrac Service Instructions Manual Download Page 49

Page: 49 / 76

INFICON

Service Instructions | 5

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

49 / 76

5.13 Open Probe P60 Cover

Part

Part no.

Qty

Consumables

P60 Probe Handle

Lower Part

598-247

LOCTITE

2400

Disassemble

Disconnect the Probe from the Sensistor Sentrac.

Use a Spanner for notched nut and slightly loosen the C21 connection port nut

(A).

Remove the two screws and the lock washers (B).

Carefully remove the lower part of the Probe handle (C).

Assemble

Place the lower part of the Probe handle (C) correctly. Make sure that the cables

are not pinched between the upper and lower part of the Probe handle and that

the lock washer is on the inside of the Probe handle.

Reinstall and tighten the two screws and lock washers (B). Use thread locking

compound.

Use a Spanner for notched nut and firmly tighten the C21 connection port nut

(A).

Summary of Contents for Sensistor Sentrac













































































Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands

Inficon Sensistor Sentrac, Service Instructions Manual

Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands