Inficon IMM-200 Operating Manual Download Page 14 | Manualshive

Page: 14 / 67

background image

4 | Introduction and Specifications

INFICON

14 / 67

074-733-P1A IMM-200 Operating Manual

4.2.3 Earth Ground

When using the optional power supply, IMM-200 is connected to earth ground through

a sealed three-core (three-conductor) power cable, which must be plugged into a

socket outlet with a protective earth terminal. If an extension cable is used, it must

always have three conductors, including a protective earth terminal. If a user supplied

power supply is used, the power supply connector must have a shield which is

grounded to AC line ground.

DANGER

Warning of Electrical Shock

Never interrupt the protective earth circuit. Any interruption of the protective earth

circuit inside or outside IMM-200 or disconnection of the protective earth terminal may

cause dangerous voltages to be present on or inside IMM-200.

This symbol indicates where the protective earth ground is connected inside IMM-200.

Never unscrew or loosen this connection.

«
...
12
13
14
15
16
...
»

Summary of Contents for IMM-200




































































Reviews:

No comments

Related manuals for IMM-200

Brand: Landoll Pages: 34

Brand: CAIRE Pages: 2

Brand: Bante Instruments Pages: 6

Brand: lancer Pages: 3

Brand: lancer Pages: 12

Brand: R2 Pages: 26

MiniLift160 Classic

Brand: Handicare Pages: 28

Brand: Hands Free Farm Pages: 24

Brand: i-Optik Pages: 75

Brand: Feniex Pages: 5

INTEGRA ARINC e-NAV

Brand: Kannad Pages: 20

FUSION Equine DR II

Brand: SOUND Pages: 178

Brand: PASCO Pages: 3

Brand: Taurus Pages: 44

Brand: ZOE Pages: 40

Brand: Waters Pages: 236

Brand: NightBalance Pages: 1

Brand: Sygonix Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands