Inficon Contura S400 Translation Of The Original Operating Instructions Download Page 54

Page: 54 / 68

8 | Cleaning and maintenance

INFICON

54 / 68

Contura® S400-Operating-instructions-jina91en1-09-(2001)

To connect the hoses to the hose connections in the lower membrane support

as closely as possible in a leak-proof manner, first press the ends of the

transparent hose into the provided connections in the lower membrane carrier.

The release rings fix the transparent hoses.

Fig. 7: Position of the hoses

1 Lower membrane support

2 Hose connections

3 Hose guides

Slide the black hose guides into a right angle arrangement. This provides strain

relief.

8.8 Velcro tape replacement

Velcro tape measurement chamber

CS4 (5.6 m in length)

Order number 200006378

Required tools

Scissors

Self-adhesive Velcro tape is attached on both membrane supports, on which the mesh

is attached. The Velcro tape can be replaced.

Velcro tape no longer functions properly or has to be replaced for reasons of age.

Gently pull the textile mesh from the Velcro tape.

Remember how the old Velcro tape is fixed and where there are incisions to

follow the curvature of the Velcro tape.

Remove the old Velcro and any adhesive residues.

Use the scissors to adjust the length of the new Velcro tape to the length of the

old Velcro tape.

Glue the new Velcro tape onto the membrane support. Make several incisions

as with the old Velcro tape to follow the curvature.

Make sure that the new Velcro tape does not touch either the black membrane

or the sealing surfaces.

You can re-attach the textile mesh, see "Replace textile mesh [

}

51]”.

Summary of Contents for Contura S400





































































Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands

Inficon Contura S400, Translation Of The Original Operating Instructions

Search results

Summary of Contents for Contura S400

Reviews:

Related manuals for Contura S400

Brands by name

Popular brands