RGB
LED
trake
RFDA-73M/RGB
Dimming actuator for LED (RGB) strips, 3-channel
EN
02-37/2015 Rev.2
Made in Czech Republic
8/10
MODE
MODE
THERM 0-10V
Description of mode THERM 0-10V /
The mode is used to control the actuator by analog inputs 0
- 10
V by using the DAC3-
04M or DAC3-04B. It is therefore possible to combine and control LED strips via iNELS.
Programming /
Using a screwdriver on the MODE potentiometer, set the THERM 0
- 10
V mode.
THERM 1-10V
Description of mode THERM 1-10V /
The mode is used to control the actuator by analog inputs
1 - 10
V by using the DAC3-
04M or DAC3-04B. It is therefore possible to combine and control LED strips via iNELS.
Programming /
Using a screwdriver on the MODE potentiometer, set the THERM 1
- 10
V mode.
1 x
Function switch off /
Description of switch off /
The dimmer output switches off by pressing the button.
Programming /
Press of programming but
-
ton on actuator RFDA-73M/
RGB for 1 second will activate
actuator RFDA-73M/RGB into
programming mode. LED is
flashing in 1s interval.
Eight presses of selected but
-
ton on the RF transmitter as
-
signs the function OFF (must be
a lapse of 1s between individual
presses).
Press of programming button
on actuator RFDA-73M/RGB
shorter then 1 second will fin
-
ish programming mode. The
LED lights up according to the
pre-set memory function.
2
8 x
1
PROG
>
1s
1 x
PROG
<
1s
1 x
3
Trokanalni dimer za LED (RGB) trake
www.elkoep.rs
U-Energister, d.o.o.| Noveških interniraca 1V | 31000 Užice | Serbia | e-mail: [email protected]
U-Energister, d.o.o. | Norveških interniraca 1V | 31000 Užice | Republika Srbija | e-mail: [email protected]
EN
Support: +381 63 479 880 |
RS
Tehnička podrška +381 63 479 880
RS
Opis režima THERM 0-10V
Režim se koristi za upravljanje elementom pomoću analognih ulaza 0 – 10V uz
pomoć DAC3-04M ili DAC3-04B. Stoga je moguće kombinovati i kontrolisati LED
trake putem iNELS
-a
.
Programiranje
Pomoću šrafcigera na potenciometru MOD podesite potreban režim THERM
0-10V.
Opis režima THERM 1-10V
Režim se koristi za upravljanje elementom pomoću analognih ulaza
1
– 10V uz
pomoć DAC3-04M ili DAC3-04B. Stoga je moguće kombinovati i kontrolisati LED
trake putem iNELS
-a
.
Programiranje
Pomoću šrafcigera na potenciometru MOD podesite potreban režim THERM
1
-10V.
Opis funkcije isključi
Izlaz zatanjenja osvetljenja isključuje se pritiskom na taster.
Programiranje
Pritiskom na taster PROG na
elementu
RFDA-73M/RGB
u trajanju od 1s, element se
prebacuje u režim programi
-
ranja. LED lampica trepće u
intervalima od 1s.
Pritiskom 8x na taster po va
-
šem izboru na RF kontroleru
dodeljuje se funkcija isključi
(između svakog pritiska taste
-
ra mora biti razmak od 1s).
Pritiskom na taster PROG na
RFDA-73M/RBG kraće od 1s,
završava se režim programi
-
ranja. LED svetli u skladu sa
podešenom funkcijom me
-
morije.
Funkcija isključi