P. I. E. INEL Sp. z o. o., ul. Mostowa 1, 80-778 Gdańsk, [email protected] www.inel.gda.pl
2.2
Installing the motor
Fix the mounting bracket (
A
) to the side of the roller blind
cassette, connect the adapter
(D)
to the thrust ring of the
motor (
C
).
Place an appropriate driver provided with the motor (
E
) on
the motor axis, secure it with a pin (
F
), and slide the entire
motor to the roller tube (
G
).
Figure 2
WARNING:
The motor is fitted with an internal thermal cut-out
which allows the roller blind to work continuously for ca. 4 min.
After this time the temperature inside the motor will exceed the
permissible value, which will cause power cut-out. Subsequent
vertical movement of the roller blind will only be possible after the
motor cools down (it can take up to twenty minutes). Using this
cut-out greatly increases the life of the drive
2.3
Electrical connections
A
monostable switch
can be connected to the motor, which will
short the control signal (black wire) with ground (grey wire)
when pressed.
The switch operates in a loop: up - stop - down - stop.
DISCONNECT POWER SUPPLY BEFORE MAKING
ANY CONNECTIONS!
Improper roller blind installation will cause the
motor to stop unexpectedly.
In order to ensure the correct operation of the motor, use
rigid hangers and stoppers in the lower slat. The length of
the curtain must be adjusted to the length of the guides.
3. REGISTERING REMOTE CONTROLS
The motor is compatible with the following remote controls: PIL-
01/04NS, 01/05/09/19PM, PIL-19/99PMT, PIL-01/05/09/19DL,
PIL-19/99DLT, PIL-01PT.
Our drives allow for two methods of entering the remote control
registration mode:
3.1 Each time after connecting to mains, each drive will
enter the registration mode for 10 seconds.
After the motor is received from the manufacturer or
if the remote control is lost, a new remote can be registered as
follows:
Connect the drive to the mains: 230 VAC. Within 10 seconds
from connecting to the mains, press the ▲ and ▼ buttons on
the remote control at the same time for the selected channel
The drive will make a short up and down movement. Within the
next 10 seconds register the channel by pressing ▲.
The registration will be confirmed by a short up-down
movement.
WARNING: The procedure will erase all previously
registered channels from the memory. This will allow to
register a remote control with a drive without another
registered remote control (new drive or lost/stolen remote).
3.2 Entering the registration mode with a previously
registered remote control.
If a remote control has already been registered, subsequent
channels of the same or another remote can be registered
without disconnecting from the mains. On the registered remote,
press the ▲ and ▼ buttons at the same time.
The roller blind will move up and down. It will remain in
registration mode for the next 10 seconds. During that time, in
order to register a new channel of the same or another remote,
select the desired channel on the remote and press the ▲
button.
This way you can register any channel to any drive, but only if
you have a previously registered remote control.
4. INVERTING MOVEMENT DIRECTION
If you need to invert the movement of the roller blind (roller blind
movement direction does not match the directions on the
remote control), you must enter programming mode (with a
previously registered remote).
Press the ▲ and ▼ buttons on the remote at the same time, the
motor will make a short up-down movement, then press STOP,
the motor will make another short up-down movement. Press ▲
and ▼ again, and then STOP, the motor will move up-down-
down-up.
WARNING:
By inverting the direction of motor movement
you will reset the drive to factory settings.
5. STARTUP
After delivery from the manufacturer the motor is factory set.
The motor will adjust to the roller blind used after making 3
stops in the upper and lower limit position. After that the
motor will be ready for use.
The motor detects low rpm caused by overload, and locks
the direction it was moving before being stopped. In order to
unlock the direction, move in the opposite direction for at
least 1 second.
Before drive startup/programming check the condition
of the curtain, guides and roller blind cassette and
whether there is a sill mounted in the window!
The roller blind cassette and guides should be free from
any contaminants and ensure unrestricted curtain
movement throughout the entire length. If the guides are
contaminated with building materials or are too tight,
they can cause damage to the drive and the roller blind,
which is not covered by the warranty.
Figure 3
N - neutral
PE - protective
L -
brown
yellow-green
black
blue
grey
