optional button / optional external signal generator at the point of
installation.
If you wish to connect a door release, please note that this requires
its own power supply (power consumption: max. 1 A at up to 15 V
AC or DC - see Fig. B). As well as this, please follow the door release
operating instructions.
If you wish to connect an external signal generator, please note that
this requires its own power supply (power consumption: max. 1 A at
up to 15 V DC - see Fig. B). As well as this, please follow the signal
generator operating instructions.
By free line of sight between a maximum wireless range of up to 100 -
150 m is possible, within buildings this is reduced to maybe 20 m.
The range cannot be guaranteed as it is dependent on the local conditions.
In order to avoid malfunctions, only one wireless system should be fitted for
each monitoring location/building/home.
A reduction of the range will be caused by:
Walls and Floors, in particular those of metal or with metal
reinforcement
Sheet metal surfaces e.g. refrigerator, metal shelves
Coated windows (eg. those with Insulating glass), radiators, and metal
surfaces
Strong electric fields and other radio equipment, eg. microwave ovens,
radio telephones, mobile phones, radio equipment in the 2.4 GHz
range, electric motors and power cables
Devices using the same or similar frequency (eg. WLAN-systems)
The additional outdoor station and the mobile unit DVT40M must be
paired in order to establish a radio connection.
To connect the additional outdoor station (max. 1 addtional outdoor
station) to the mobile unit, proceed as follows:
The outdoor station and mobile unit must both have a power supply
and the mobile unit must be switched on.
Press any button [1/2/3/5/7/8] on the mobile unit to make the
start screen appear.
Press the left button
[3 - “Menu”] to open the menu.
Scroll through the menu with the
and
[2] buttons until you
reach "Register" and press the left button
[3 - “Select”].
Channel no. 1 and no. 2 appear, the hash # indicates which
channel is currently selected.
Move the hash # to the channel you require by pressing [2]:
First mobile unit:
Channel no. 2 for second door intercom
Second mobile unit:
Channel no. 1 for second door intercom
Channel no. 2 for second door intercom
Press the left button
[3 - “
”]. The mobile unit beeps and
you now have approx. 20 seconds to complete pairing.
Press and hold the pairing button [28] on the outdoor station until
you hear three short beeps on the outdoor station as confirmation
that pairing has been successful; the mobile unit then makes a
"plop" sound and the start screen appears again.
!
!
!
!
!
!
!
!
!
Wireless range
#
#
#
#
#
—
—
—
8. Pairing with the mobile unit
Information about operation following extension:
Notes:
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
#
#
!
If there is a ring at one of two outdoor stations, you can see at the
top left of the camera image where the ring has come from: outdoor
station "1#" or "2#".
When there is a ring at one of the
, all of the paired
mobile units that are switched on respond as described in section 11.1.
If there is a ring at a
and the conversation is
accepted on one of two paired mobile units, the camera image
switches off on the other mobile unit, the start screen appears on it
and the screen switches off after approx. 20 seconds.
Remove the
[20] from the safety cover [33].
Hold the mounting bracket in the desired location, mark the
position of the two fitting holes to be drilled [37] and of a hole for
the cable if necessary [36].
Drill the two fitting holes and insert two plugs [40] if required.
If necessary, drill a suitable hole through which to feed the cable for
the power supply to the
and any other connection
cables for the optional door release and/or external signal
generator (e.g. an external bell) and/or optional button for opening
the door.
Note: A flush-mounted socket in the wall directly above the cable
opening may be helpful to make cable connection easier.
Feed all the connection cables required through the drilled hole and
through the cable opening in the protective cover.
Fix the mounting bracket to the wall using two screws [39].
If batteries are to be used:
Release the battery compartment cover [31] screw and lever the
cover from the outdoor station.
Insert 2 pcs. LR14 (C), 1,5 V alkaline batteries (not supplied)
into the battery compartment, paying attention to the polarity.
Do not use rechargeable batteries.
Refix the cover onto the outdoor station with the screw.
Set the energy consumption mode if necessary, as described in
the note in section 11.2
.
Carefully lever the plastic cover off the name plate [19], remove the
name plate, label it, re-insert the name plate and replace the
plastic cover over it.
If connecting a power supply unit and/or other devices, follow
connection diagram B:
Only one wire should be inserted into each terminal connection.
A maximum of 2 J-Y(St)Y wires with a diameter of 0.6 twisted
together may, however, be inserted into one terminal. With
three wire ends, a terminal strip or connector must be used to
join the wires before the terminal connection.
The exposed wire end (10-12 mm) must be inserted fully into
the terminal connection.
To connect a 9-12 V DC power supply unit, attach the two wires
of the supply unit to the GND and DC9-12V power connection
outdoor stations
outdoor station
outdoor station
outdoor station
9. Fitting and connection
in the operating instructions of the
basic set
15
