background image

4

GB

A

V

!

 If one or more of these conditions is not fulfilled or

if the cooker must be installed according to the
conditions listed for class 2 - subclass 1 appliances
(installed between two cupboards), the flexible steel
hose must be used instead (

see below).

Connecting a flexible jointless stainless steel pipe
to a threaded attachment

Make sure that the hose and gaskets comply with
current national legislation.
To begin using the hose, remove the hose holder on the
appliance (the gas supply inlet on the appliance is a
cylindrical threaded 1/2 gas male attachment).

!

 Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres,
making sure that the hose is not compressed and
does not come into contact with moving parts.

Checking the connection for leaks

 When the installation process is complete, check
the hose fittings for leaks using a soapy solution.
Never use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas
other than the default type (this is indicated on the
rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:
1. Remove the hob grids and slide the burners off
their seats.

2. Unscrew the nozzles using a
7 mm socket spanner (

see

figure), and replace them with
nozzles suited to the new type
of gas(

see Burner and nozzle

specifications table).
3. Replace all the components
by following the above

instructions in reverse.

Adjusting the hob burners’ minimum setting:
1. Turn the tap to the minimum position.
2. Remove the knob and adjust the regulatory
screw, which is positioned inside or next to the tap
pin, until the flame is small but steady.

!

 If the appliance is connected to a liquid gas

supply, the regulatory screw must be fastened as
tightly as possible.

3. While the burner is alight, quickly change the position
of the knob from minimum to maximum and vice versa
several times, checking that the flame is not
extinguished.

!

 The hob burners do not require primary air adjustment.

Adapting the oven

Replacing the oven burner nozzle:
1. Remove the oven compartment.

2. Slide out the protection
panel A
(

see diagram).

3. Remove the oven burner
after unscrewing the screws V
(

see figure).

The whole operation will be
made easier if the oven door
is removed.

4. Unscrew the nozzle using a
special nozzle socket spanner
(

see figure) or with a 7 mm

socket spanner, and replace it
with a new nozzle that is
suited to the new type of gas
(

see Burner and nozzle

specifications table).

Adjusting the gas oven burner’s minimum setting:

1. Light the burner (

see Start-up and Use).

2. Turn the knob to the minimum position (MIN) after
it has been in the maximum position (MAX) for
approximately 10 minutes.
3. Remove the knob.
4. Tighten or loosen the adjustment screws on the
outside of the thermostat pin (

see figure) until the

flame is small but steady.

!

 If the appliance is connected to liquid gas, the

adjustment screw must be fastened as tightly as
possible.

Summary of Contents for KN1G21S/HU

























Reviews: