Indesit IWB 70852 C ECO HK, Instruction & Installation Manual, Page: 7 / 16

5
洗衣劑投放盒：加入洗滌劑及柔順劑。
(
見第
10
頁
)
Detergent dispenser drawer : used to dispense detergents
and washing additives (see page 10).
開/關電源掣：
按下此鍵操控洗衣機開/關。
ON/OFF button: switches the washing machine on and off.
洗衣程序選擇旋鈕：
選擇旋鈕可順時針或逆時針方向旋轉。當程序選定後，選擇旋
鈕會停留所選號碼直至程序完畢。
WASH CYCLE knob: programmes the wash cycles.
During the wash cycle, the knob does not move.
功能選擇掣連指示燈：
按下按鈕選擇所需的功能，可選多項。燈亮著表示該功能已被
接受。如指示燈閃亮後自動熄滅，代表該功能不適用於設定之
洗滌程序。
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function with remain lit.
溫度選擇旋鈕：
用作選擇洗衣溫度或冷水洗滌。
(
見第
8
頁
)
TEMPERATURE knob: sets the temperature or the cold
wash cycle (see page 8).
洗衣過程/預校開機時間指示燈：
洗衣程序進行中，指示燈會按洗衣狀況順序亮起。
設定所需的預校開機時間，指示燈會在所選之時間上亮著。
WASH CYCLE PROGRESS / DELAY TIMER indicator
lights: used to monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
If the Delay Timer function has been set, the time remaining
until the wash cycle starts will be indicated.
門鎖指示燈：燈亮著表示機門處於鎖閉狀態。
(
見下頁
)
DOOR LOCKED indicator light: Indicates whether the
door may be opened or not (see next page).
開始/暫停掣連指示燈：
用作開始洗衣程序或暫停洗衣程序。
注意︰如需在洗衣程序中暫停運作，按下此掣，指示燈轉為
橙色並且閃動；門鎖燈 熄減，機門可以打開 (約待3分鐘)。
在洗衣程序中斷後要繼續運作，再按下掣。
START / PAUSE button with indicator light: starts or
temporarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened
(wait approximately 3 minutes).
To start the wash cycle from the point at which it was
interrupted, press this button again.
備用模式
此洗衣機符合節能新規例，附設一個自動備用系統，當啟動
本機約
30
分鐘後，如仍檢測不到任何指示，將會自動進入備
用模式。要重新開機，只需按下電源掣。
Standby mode
This washing machine, in compliance with new energy saving
regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.