Indesit IS50G, Operating Instructions Manual

Page: 3 / 16

GB
3
Gas connection
T he cooker should be connected to the gas-supply
by a Gas Safe registered installer. During installation of
this product it is essential to fit an approved gas tap
to isolate the supply from the appliance for the
convenience of any subsequent removal or
servicing. Connection of the appliance to the gas
mains or liquid gas must be carried out according to
the prescribed regulation in force, and only after it is
ascertained that it is adaptable to the type of gas to
be used. If not, follow the instructions indicated in
the paragraph headed “Adaptation to different gas
types”. On some models the gas supply can be
connected on the left or on the right, as necessary;
to change the
connection, reverse the
position of the hose
holder with that of the
cap and replace the
gasket (supplied with
the appliance). In the
case of connection to
liquid gas, by tank, use
pressure regulators that
conform to the
regulation in force. The gas supply must be
connected to the left of the appliance. Be sure that
the hose does not pass through the rear of the
cooker touching hot parts.
! Make sure the supply pressure conforms with the
values shown in the table entitled “Caracteristics of
the burners and nozzles”. When the cooker is
When the cooker is
When the cooker is When the cooker is When the cooker is
installed between cabinets (recessed), the installed between cabinets (recessed), the
installed between cabinets (recessed), the installed between cabinets (recessed), the installed between cabinets (recessed), the
gas connection must be effected by an
gas connection must be effected by an gas connection must be effected by an gas connection must be effected by an gas connection must be effected by an
approved flexible hose with bayonet fitting
approved flexible hose with bayonet fitting approved flexible hose with bayonet fitting approved flexible hose with bayonet fitting approved flexible hose with bayonet fitting
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for (BS 669 Current Edition). The gas inlet for
(BS 669 Current Edition). The gas inlet for
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female
the cookers is a threaded G 1/2 gas female the cookers is a threaded G 1/2 gas female the cookers is a threaded G 1/2 gas female
f i t t i n g .
f i t t i n g . f i t t i n g . f i t t i n g . f i t t i n g .
Connecting the gas supply
To make the connection, a flexible hose should be
used corresponding to the current gas regulations
which are:
• the hose must never be at any point in its lenght
in contact with the “hot” parts of the cooker;
• the hose must never be longer than 1,5 metre;
• the hose must not be subject to any tension or
torsional stress and it must not have any
excessively narrow curves or bottlenecks;
• the hose must be easy to inspect along its entire
length to check its condition;
* Only available in certain models
• the hose must always be in good condition, never
attempt to repair.
! The installation must comply with gas safety
(installation and use) regulations 1984. In all cases
for the above, by low, a qualified, Gas Safe approved
engineer must be called for installation.
Electrial connection
Power supply voltage and frequency: 230-240V a.c.
50/60 Hz.
!!!!! The supply cable must be positioned so that it
never reaches at any point a temperature 50°C
higher than the room temperature. The cable must
be routed away from the rear vents. Should you
require it, you may use a longer cable, however, you
must ensure that the cable supplied with the
appliance is replaced by one of the same
specifications in accordance with current standards
and legislation.
Your appliance is supplied with a 13 amp fused plug
that can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
WARNING - THIS APPLIANCE MUST BE
EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words on
the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug
and you should wish to remove it to add a cable
extension or to re-route the mains cable through
partitions, units etc., please ensure that either:
• the plug is replaced by a fused 13 amp re-
wireable plug bearing the BSI mark of approval.
or:
700 mm
HOT PARTS