background image

10

GB

Installation

A

Positioning the Appliance

Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned
to the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher,
making it level. In any case, the appliance should not be
inclined more than 2°.
If the appliance is level, it will help ensure proper perfor-
mance.

This dishwasher model can be built under a single worktop
(please read the relevant instruction sheet).

Cold water connection.

This electric household appliance should be connected to
the water mains using the cold water supply hose provided
with the appliance only. Do not use a different hose. In the
event of replacements, use original spare parts only.
Connect the cold water supply hose to a 3/4 gas threaded
connection, taking care to screw it tightly onto the tap.
If the water hoses are new or have been out of use for an
extended period of time, let the water run to make sure it is
clear and free of impurities before making the connection.
If this precaution is not taken, the water inlet could get
blocked, causing damage to your dishwasher.

Drain Hose Connection

Fit the drain pipe into a drain
line with a minimum diameter
of 4 cm or place it over the
sink. Avoid restricting or
bending it. Use the special
plastic elbow provided (see fi-
gure) to position it in the best
possible way. The part of the
pipe marked with the letter A
should be between 40 and
100 cm above the ground.
The pipe should not be immersed in water.

Attention

: The special plastic hose support must be solidly

fastened to the wall to  prevent the drain hose from moving
and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values
for the current in the home correspond to those on the
rating plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.

Should the electricity supply cable be damaged, we
recommend that you only contact authorised Technical
Service Centres for the replacement.

Caution

: the dishwasher plug must be accessible  even

when the appliance is installed as a built-in unit so that
maintenance  can be done safely.

Summary of Contents for IDL 60

















Reviews: