background image

11

GB

Installation

A

Positioning the Appliance

Position the appliance in the desired location. The back
should rest against the wall behind it, and the sides, along
the adjacent cabinets or wall. The dishwasher is equipped
with water supply and drain hoses that can be positioned
to the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing
them in or out) to adjust the height of the dishwasher,
making it level. In any case, the appliance should not be
inclined more than 2°.
If the appliance is level, it will help ensure proper perfor-
mance.

This dishwasher model can be built under a single worktop
(please read the relevant instruction sheet).

Cold Water Connection

This electric household appliance should be connected to
the water mains using the cold water supply hose provided
with the appliance only. Do not
use a different hose. In the
event of replacements, use
original spare parts only.
Connect the cold water supply
hose to a threaded 3/4 (gas)
connector, inserting the small
filter supplied with the
dishwasher and making sure
that it is fastened tightly in place
(see figure 2).
If the water pipes are new or
have not been used for an extended period of time, let the
water run to make sure that the water is clear and free of
impurities. If this precaution is not taken, there is a risk that
the water inlet can get blocked and damage the appliance.

Hot Water Connection

The water supply to the appliance can also be connected to
the house's hot water line (centralised system, heating
system), as long as it does not exceed a temperature of  60°
C.
In this case, the wash cycle time will be shortened by about
15 minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following
the same procedures as those for the connection to the cold
water line.

Drain Hose Connection

Fit the drain pipe into a drain
line with a minimum diameter
of 4 cm or place it over the
sink. Avoid restricting or
bending it. Use the special
plastic elbow provided (see fi-
gure) to position it in the best
possible way. The part of the
pipe marked with the letter A
should be between 40 and
100 cm above the ground.
The pipe should not be immersed in water.

Attention

: The special plastic hose support must be solidly

fastened to the wall to  prevent the drain hose from moving
and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values
for the current in the home correspond to those on the
rating plate (located on the stainless steel inner door of the
appliance) and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into
an electrical socket which is earthed properly (the earthing
of the appliance is a safety requirement mandated by law).
If the electrical socket to which the appliance must be
connected is not appropriate for the plug, replace the plug,
rather than using adpators or the like as they could cause
overheating and burns.

Should the electricity supply cable be damaged, we
recommend that you only contact authorised Technical
Service Centres for the replacement.

The plug

The dishwasher plug must be accessible even when the
appliance is installed as a built-in unit so that maintenance
can be done safely.

A

Fig.2

Summary of Contents for IDE 1000UK














Reviews: