background image

9

GB

Cleaning and Special Maintenance

Filter Assembly

If you want consistent good results from your dishwasher,
you need to clean the filter assembly.
The food particles
are removed from
the wash water,
allowing it to be
recirculated during
the cycle, filtered
perfectly. For this
reason, it is a good
idea to remove the
larger food
particles trapped
inside the cup “

C

” and the semi-circular filter 

A

 after each

wash; pull the cup handle upwards to remove them. Just
rinse them under running water.
The entire filter assembly should be cleaned thoroughly once
a month: cup C + semi-circular filter A + cylindrical filter B.
Rotate filter “B” anticlockwise to remove it.
For cleaning, use a non metallic brush.
Reassemble the filter parts (as shown in the figure) and

reinsert the whole
assembly into the
dishwasher. Position it
into its housing and
press downwards.
The dishwasher is not
to be used without
filters. Improper
replacement of the
filters may reduce the
efficiency of the wash and even damage your dishwasher.

Cleaning the Sprayer Arms

It may happen that food particle become encrusted on the
sprayer arms and block the holes (see "Close up view
(interior)", letters F-I). Check the sprayer arms periodically
and clean them when needed.

Cleaning the Water Inlet Filter

Periodically clean the water inlet filter (see figure 2 under
"Installation") located on the outlet of the water supply
tap. After turning off the water tap, unscrew the end of
the water supply hose, remove the filter and clean it carefully
under running water. Then, return the filter to its place and
tighten the water supply hose back into position.

Troubleshooting

It may occur that the dishwasher does not function or does
not function properly. Before calling for assistance, let us
see what can be done first: have you forgot to press one of
the buttons or to perform an essential operation?

The Dishwasher Does Not Start

Have you checked whether:

- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on "ON";
- the water supply is turned on.
 

The Dishwasher Does Not Load Water

Have you checked whether:

- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient
  pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
 

The Dishes Are Not Clean

Have you put the right amount of detergent into the
dispenser?
Is the wash cycle suitable for the dishes you have placed
inside the appliance?
Are the filter and microfilter clean?
Can the sprayer arms turn freely?

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

- the lid to the salt container is closed properly;
- the rinse aid dosage is correct.

Error messages

Your dishwasher is equipped with a safety system which is
able to detect any operating anomalies. These anomalies
are reported by one or two cycle phase indicator lights "

G

"

flashing rapidly. Take a note of which lights are flashing,
turn the appliance off and call for technical assistance.

Tap off alarm

If you have forgotten to turn the water tap on, your appliance
will remind you of this by sounding a few short beeps for a
few minutes. Turn the tap on and your appliance will start
up again after a few minutes. Were you to be absent when
these beeps are sounded, the appliance will be blocked
automatically and cycle phase 2 and 3 indicator lights (wash
and rinses) will flash rapidly. Turn the appliance off at the
ON-OFF button, turn on the water tap and wait
approximately 20 seconds before turning the appliance back
on, now the program will start.

If, despite all these checks, the dishwasher still does not
function and/or the problem persists, contact the nearest
authorised service centre and provide them with the
following information:
- the nature of the problem;
- the model type number (Mod. ...) and the serial number
(S/N ....), which are indicated on the plate located on the
side of the inner part of the door.

Never call on unauthorised technicians and refuse to
allow parts to be installed that are not original spare
parts

1

2

A

B

C

Summary of Contents for DI 67

















Reviews: