Incra Miter 1000HD Owner'S Manual Download Page 7

Page: 7 / 8

IncrA

MIteR1000HD

Owner’s MAnuAl

page 7

Making a Zero Clearance Wooden Sub
Fence

A sub fence can be used to provide tear out control as
well as support for your workpiece up to and beyond the
blade. A good material to use for making your zero
clearance sub fence is 3/4” medium density fiberboard
(MDF). Use the drill and counter bore dimensions
shown in

Fig. 18

. Attach using the supplied fasten-

ers.  Adjust the length of the fence to accommodate
your  application.    Note:    In  applications  where  the
incremental stopping capability of the Flip Shop Stop
is  required,  the  wooden  sub  fence  can  be  no  taller
than 2-1/2”.

Expanded Flip Stop Clamping Mode

The  two-part  body  design  of  the  INCRA  Flip  Shop
Stop allows for use with up to a 3/4” thick wooden sub
fence.  To expand the INCRA Flip Shop Stop, loosen
the (2) socket head screws located on the top of the
stop  body,  then  slide  the  upper  portion  of  the  stop
off.  Now slide the upper portion back on, capturing
the rectangular nuts in the second T-slot located on
the lower portion (gold component) of the stop body,

Fig.19

To avoid the saw blade pulling your workpiece into the cut, add a strip of adhesive backed sandpaper to the front
face of the wooden sub fence.

TIP

WARRANTY

TAYLOR DESIgN gROUP, INC. WARRANTS THIS PRODUCT FOR ONE YEAR FROM DATE OF PURCHASE.  WE
WILL REPAIR ANY DEFECTS DUE TO FAULTY MATERIAL OR WORkMANSHIP, OR AT OUR OPTION, REPLACE
THE PRODUCT FREE OF CHARgE.  PLEASE RETURN THE FAILINg COMPONENT ONLY, POSTAgE PREPAID,
ALONg WITH A DESCRIPTION OF THE PROBLEM TO THE ADDRESS BELOW.  THIS WARRANTY DOES NOT
APPLY TO PARTS WHICH HAvE BEEN SUBJECTED TO IMPROPER USE, ALTERATION, OR ABUSE.

LIFETIME WARRANTY ON POSITIONING RACKS

IF AN INCRA POSITIONINg RACk IN THIS TOOL BECOMES DAMAgED FOR ANY REASON, TAYLOR DESIgN
gROUP WILL REPLACE IT FREE OF CHARgE FOR AS LONg AS YOU OWN YOUR TOOL. RETURN THE DAM-
AgED RACk, POSTAgE PREPAID, PLEASE ALLOW 1 TO 2 WEEkS FOR DELIvERY.

Fig. 18

Making a Sub Fence

Fig. 19

Expanded Flip Stop Clamping Mode

2-1/2” max (see note)

5/16” through hole w/

3/4” dia. x 3/8” deep

counter bore

1/4-20

rectangular nut

1/4” flat washer

1/4-20 x 3/4”

socket head screw

1-1/16”

3/4”

Gold component

Loosen socket head

screws and slide red

assembly into 2

T-slot

on gold component

Sub fence

Summary of Contents for Miter 1000HD









Search results

Summary of Contents for Miter 1000HD

Reviews:

Related manuals for Miter 1000HD

Brands by name

Popular brands

Incra Miter 1000HD, Owner'S Manual

Search results

Summary of Contents for Miter 1000HD

Reviews:

Related manuals for Miter 1000HD

Brands by name

Popular brands