22
23
Installation
Installation
Gas Connection
Gas Specification
Where a flexible hose assembly is used, ensure it is
approved to AS/NZS 1869, Class B. Any hose assembly
used must be restrained from accidental contact with
the flue outlet of an under bench oven.
This hose assembly shall be suitable for connection to a
fixed consumer piping outlet located as follows:
Hotplates at a point 800 mm to 850 mm above the floor
and in the region outside the width of the appliance to a
distance of 250 mm.
After connecting to gas, check for leaks using soapy
solution, never a naked flame.
Inlet connection region for flexible hose
Gas Connection
Install in accordance with relevant gas standards and/or codes of
practice applicable.
Connect the elbow fitting to the appliance gas manifold
connection, and check that seals between the elbow and
manifold connection are in place and in good condition.
For Natural gas: connect the natural gas appliance
regulator (pictured opposite) with integral test point using
approved gas thread tape or compound to the elbow
fitting.
For Universal LPG: connect the brass test point adaptor
(pictured opposite) using approved gas thread tape or
compound to the elbow fitting.
Ensure the supply connection point, test point and natural gas
regulator adjustment screw (for Natural gas installation) are
accessible for testing and/or adjustment with the hotplate in
the installed position.
20
■
■
■
Flexible Hose: If installing with a hose assembly, it must comply with AS/NZS
1869,10mmID,class B or D,no more than 1mm long and installed in
accordance with AS/NZS 5601.1.
Ensure that the hose does not contact the hot surfaces of the
hotplate,oven,dishwasher or any other appliance that may be installed
underneath or next to the hotplate.The hose should not be subjected to abrasion,
kinking or permanent deformation and should be able to be inspected along its
entire length with the cooktop in the installed position. Unions compatible with
the hose fittings must be used and all connections tested for gas leaks.The
supply connection point shall be accessible with the appliance installed.
WARNING: Ensure that the hose assembly is restrained from accidental contact
with the flue outlet of an underbench oven.
Gas Connection
Gas Specification
21
Wok burner
Rapid burner
Semi-rapid
Auxiliary-rapid
10.8MJ/h
6.3MJ/h
3.6MJ/h
0.88
0.68
0.53
1.50
1.12
0.83
12.96MJ/h
0.97
1.60
Heat input and orifice size marked(mm)
Gas type &
pressure
Propand
2.75kPa
Natural Gas
1.0kPa
Model: ICGG604W
Model: ICGG755W & ICGG905W
23
Installation
Gas Specification
Gas Specification
21
Wok burner
Rapid burner
Semi-rapid
Auxiliary-rapid
12.96MJ/h
6.3MJ/h
0.
97
0.68
0.56
1.
6
0
1.12
0.90
/
/
/
Heat input and orifice size marked(mm)
Gas type &
pressure
Propand
2.75kPa
Natural Gas
1.0kPa
Gas Specification
21
Wok burner
Rapid burner
Semi-rapid
Auxiliary-rapid
10.8MJ/h
6.3MJ/h
3.6MJ/h
0.88
0.68
0.53
1.50
1.12
0.83
12.96MJ/h
0.97
1.60
Heat input and orifice size marked(mm)
Gas type &
pressure
Propand
2.75kPa
Natural Gas
1.0kPa
Model: ICGG604W
Model: ICGG755W & ICGG905W
4.0MJ/h
Auxiliary
Auxiliary
ULPG
ULPG