background image

STEP 3    (See Diagram 3) 

A.)  Attach the Front Press Base (#11) to the Upper Frame (#4). Secure it with one Long Axle 

(#46), two Ø ¾” Washers (#83), and two M10 Aircraft Nuts (#85). 

B.)  Attach the Right Butterfly (#6) to the Front Press Base (#11). Secure it with one Ø 1 ½” 

Washer (#82), one M6 x 1 ¼” Allen Bolt (#78), Lock Ring (#41), and M6 Aircraft Nut (#86).  

C.)  Slide a Butterfly Foam Roll (#62) onto the Right Butterfly arm. Attach the Right Front Press 

Handle (#13) to the Right Butterfly. Secure it with a M10 x 1” Allen Bolt (#73) and Ø ¾” 
Washer (#83). 

D.)  Repeat the Steps B&C above to install the Left Butterfly (#5). 
E.)  Attach a Butterfly Pulley Bracket (#9) to the Upper Vertical Frame (#14). Secure it with one 

M10 x 2 3/8” Allen Bolt (#71), two Ø ¾” Washers (#83), and one M10 Aircraft Nut (#85).  

F.)  Attach Swivel Pulley Brackets (#21) to each end of the Butterfly Pulley Bracket. Secure each 

Bracket with one M10 x 2 ½” Allen Bolt (#70), two Ø ¾” Washers (#83), and one M10 Aircraft 
Nut (#85).  Do Not over tighten! Make sure the Brackets are able to swivel freely. 

G.)  Attach the Backrest Board (#39) to the Vertical Frame. Secure it with two M8 x 3” Allen Bolts 

(#75) and Ø 5/8” Washers (#84). 

 

11 

Summary of Contents for Marcy MCH-1510























Reviews: