manualshive.com logo in svg

Impex COMPETITOR WM-357, Owner'S Manual, Page: 6 / 13

Share
Download
Impex COMPETITOR WM-357 Owner'S Manual Download Page 6

ASSEMBLY INSTRUCTION 

 

Tools Required Assembling the Machine:  Two Adjustable Wrenches and Allen 
Wrenches 

 

NOTE:  It is strongly recommended two or more people assembling this machine to 
avoid possible injury. 

 

STEP 1 (See Diagram 1) 

A.) Plug the two Upright End Caps (#24) onto the bottom of the Right & Left Upright 

Beams (#1 & #2). Secure each Cap with a ST5 Screw (#47). 

B.) Connect the two Upright Beams by a Cross Brace (#4) in the Mid-span. Secure them 

with two M10 x 3 1/8” Carriage Bolts (#36), one Curved Bracket (#14), two 

∅

 ¾” 

Washers (#43), and two M10 Aircraft Nuts (#48) on each end of the Cross Brace. 

C.) Attach a Weight Post (#8) to the Right Upright Beam. Secure it with one M10 x 1” 

Allen Bolt (#40) and Curved Washer (#46). Slide a 2 3/8” Rubber Bumper (#20) onto 
the Weight Post. Attach a Spring Clip (#26) to the Post. Repeat the same step to 
install the other side.  

D.) Place the Backrest Adjustment Bar (#35) between the two Uprights to obtain desired 

incline of Backrest. 

 

5 

Summary of Contents for COMPETITOR WM-357














Reviews:

No comments