background image

6

IMPERIAL TRUCK MOUNTED VACUUM TANKER MANUAL

SAFETY PRECAUTIONS

Safety Precautions for Operating Equipment

  DANGER

:  Stop  the  truck  motor,  remove  all 

persons from the truck cab, and chock the truck tires 
before  servicing  any  component  under  the  truck; 
this includes lubricating the vacuum pump or the 
PTO driveline. Contact with a rotating mechanism 
can cause entanglement that can lead to death. A 
truck  that  begins  to  roll  is  a  crushing  hazard  that 
can lead to death.

 WARNING

: Keep hands, feet, hair, and clothing 

away  from  moving  parts.  Contact  with  a  moving 
mechanism can cause entanglement that can lead 
dismemberment or death.

 WARNING

: Escaping hydraulic oil under pressure 

can have suffi cient force to penetrate your skin, which 
can cause serious injury. Before operating hydraulic 
components, be sure all connections are tight and 
hoses are not damaged. Relieve all pressure before 
disconnecting hydraulic lines or repairing leaks.

 CAUTION

: When  off-loading  under  pressure, 

maintain control of the end of the hose. Pressurized 
discharge can cause a hose end to whip about and 
create the potential for spraying persons in the area 
with effl uent.

 

 WARNING

: Keep all shields in place. Shields and 

covers  are  designed  to  protect  the  operator  from 
entanglement in moving parts, which can lead to 
serious  injury  or  death.  DO  NOT  remove  shields 
from the unit except when servicing; then, replace 
immediately.

 WARNING

: The truck’s cornering and braking 

abilities are reduced when the tank is loaded. Drive 
at a reasonable speed with a loaded tank; reduce 
speed on rough or hilly terrain, before making an 
anticipated stop, and when cornering.

 

 WARNING

:

 

Make certain everyone is clear of the 

tanker truck and the immediate area before starting 
the  engine,  engaging  power,  and  operating  the 
equipment. The inherent hazards of septic pumping 
can  cause  serious  injury  or  death  to  untrained 
persons that enter this area.

 

 WARNING:

  DO  NOT  allow  anyone  to  ride  on 

the outside of the tanker truck when it is in motion. 
Failure  to  follow  this  precaution  could  result  in 
persons falling off the truck and possibly getting run 
over, which could cause serious injury or death. 

 

 WARNING

: Before backing-up the truck, inspect 

the area to be backed into, and clear all hazards, pets, 
and  people  from  it.  Make  sure  that  backup  lights 
and the back-up alarm are maintained and in good 
working condition. Because of the truck mounted 
tank,  the  driver  will  experience  a  large  blind  spot 
behind  the  truck.  Fatalities  have  occurred  when 
persons were run over by a tanker truck.

 

 CAUTION:

 Avoid contact with the vacuum pump 

during  or  immediately  after  operation.  Operating 
temperatures  can  range  from  near  200

o

F  to  over 

00

o

F, depending on the make and  model of pump 

and on the working conditions. Contact with a hot 
vacuum pump can cause severe burns.

��������������������������������������������

������������ ���� ���� ��������� �����

�������������������������������������

������������������������������������������

�������������������������������������������

������������������������������������������

WARNING

�����������������������

��������������������������

Summary of Contents for TMV-1500































Reviews: