impact VSD-160 Instructions Manual Download Page 16

One-Year Limited Warranty

This IMPACT product is warranted to the original purchaser to be free from 

defects in materials and workmanship under normal consumer use for a period of 

one (1) year from the original purchase date or thirty (30) days after replacement, 

whichever occurs later. The warranty provider’s responsibility with respect 

to this limited warranty shall be limited solely to repair or replacement, at the 

provider’s discretion, of any product that fails during normal use of this product in 

its intended manner and in its intended environment. Inoperability of the product 

or part(s) shall be determined by the warranty provider. If the product has been 

discontinued, the warranty provider reserves the right to replace it with a model 

of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, 

accident, alteration, abuse, improper installation or maintenance. EXCEPT AS 

PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS 

WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED 

TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and 

you may also have additional rights that vary from state to state. 
To obtain warranty coverage, contact the Impact Customer Service Department 

to obtain a return merchandise authorization (“RMA”) number, and return the 

defective product to Impact along with the RMA number and proof of purchase. 

Shipment of the defective product is at the purchaser’s own risk and expense.
For more information or to arrange service, visit www.impactstudiolighting.com 

or call Customer Service at 212-594-2353.

Product warranty provided by the Gradus Group.

www.gradusgroup.com

IMPACT is a registered trademark of the Gradus Group.  

© 2014 Gradus Group LLC. All Rights Reserved.

GG3

Summary of Contents for VSD-160

















Reviews: