manualshive.com logo in svg

impact VSD-160, Instructions Manual

Share
Download
impact VSD-160 Instructions Manual Download Page 1

VSD Series Monolight

INSTRUCTIONS

www.impactstudiolighting.com

impact

Page 16

(back cover)

Page 1

(front cover)

10M

25M

50M

75M

100M

10Y

25Y

50Y

75Y

100Y

To see all of our lighting equipment,

please visit our Web site.

Impact provides a limited warranty that this product is free from defects in 
materials and workmanship to the original purchaser under normal use for a 
period of one (1) year from the original purchase date. Impact’s responsibility 
with respect to this limited warranty shall be limited solely to repair or 
replacement, at its option, of any product which fails during normal consumer 
use. This warranty does not extend to damage or failure which results from 
misuse, neglect, accident, alteration, abuse, improper installation or 
maintenance. To obtain a replacement during the time of this warranty, 
please return the defective item with proof of purchase along with an RMA 
number to the place of purchase. This warranty gives you specific legal 
rights, and you may also have other rights which vary from state to state.

©Copyright 2009 Impact

Summary of Contents for VSD-160

















Reviews:

No comments

Brands by name

Popular brands

Load more brands