iMotion SC111 User Manual Download Page 93

Page: 93 / 260

iWaylink Inc.

5-4-2 Move Commands

—

Move the cursor forward a number of characters

Move the cursor ahead “nn” characters from current cu

rsor position.

Syntax = F5nn

where nn is the numeric value (00-99) for the number of

characters the cursor should be moved ahead.

Example: Move the cursor forward and send the data

Move the cursor forward 3 characters, then send the rest of the barcode data

from the barcode above. End with a carriage return.

Command string: F503F10D

“Move the cursor forward a number of characters” command

Number of characters to move the cursor

“Send all characters” command

Hex value for a CR

The data is output as:

4567890ABCDEFGHIJ

<CR>

—

Move the cursor backward a number of characters

Move the cursor back “nn” characters from current cursor position.

Syntax = F6nn

where nn is the numeric value (00-99) for the number of

characters the cursor should be moved back.

—

Move the cursor to the beginning

Move the cursor to the first character in the input message.

Syntax = F7.

Example: Manipulate barcodes that begin with a 1 (FE and F7)

Summary of Contents for SC111





































































































































































































































































Search results

Summary of Contents for SC111

Reviews:

Related manuals for SC111

Brands by name

Popular brands

iMotion SC111, User Manual

Search results

Summary of Contents for SC111

Reviews:

Related manuals for SC111

Brands by name

Popular brands