background image

34

INS

TALLER

US

ER

MAINTEN

AN

CE TECHNI

CI

AN

Id 

Parameter

Parameter

Description

Range

Default

Personali-

zed value

A0

Hydraulic model Defines the type of hydraulics in the boiler

Set

0

0

A1

-

Not used on this boiler model

-

-

A2

Model 

Pump

Defines the type of circulator in the boiler

Set

2

2

A3

Maximum pump 

speed

Sets the maximum pump operating speed

1 ÷ 9

-

A4

Minimum pump 

speed

Sets the minimum pump operating speed

1 ÷ A3

-

A5

Pump operating 

mode

Sets the pump operating mode

Set

0

-

A7

Ignition phase 

automatic vent

Sets the activation mode of the automatic vent at each new electric powering 

phase of the boiler.

This function lasts 8 minutes, and is displayed via a countdown signalled by 

the special indicator (Ref. 14 Fig. 2-1). During this period the DHW and CH 

functions are not active. The “automatic vent” function can be annulled by 

pressing the “reset” button.

1:  the automatic vent is enabled at each new electric power supply.
0:  the automatic vent is enabled only at the first electric power supply 

after having set the parameter to “0”; once the function has ended, or 

is interrupted by pressing the “reset” button, it will not be enabled again 

unless the parameter is set to “1”.

0 - 1

1

Id 

Parameter

Parameter

Description

Range

Default

Personali-

zed value

F0

Equivalent length 

flue

Defines the length of the flue (see par. 3.10)

0 - 2

0

F1

-

Not used on this boiler model

-

-

In the event of an alteration, anomaly “E72” appears and fast calibration is required.

3.13 SOLAR PANELS COUPLING 

FUNCTION.

The boiler is set-up to receive pre-heated water 

from a system of solar panels up to a maximum 

temperature of 65°C. In all cases, it is always 

necessary to install a mixing vale on the hy-

draulic circuit upstream from the boiler on the 

cold water inlet.

Note:

 in order for the boiler to work properly, the 

temperature selected on the solar valve must be 

5°C greater than the temperature selected on the 

boiler control panel.
In this condition, parameter t2 (DHW ther-

mostat) must be set at “1” and parameter t3 

(solar delay time) must be set for a period that 

is sufficient to receive water from a storage tank 

located upstream of the boiler. The greater the 

distance from the storage tank, the longer the 

stand-by time to be set. Once these adjustments 

have been made, when the temperature of the 

boiler inlet water is the same or greater than that 

set by the DHW selector switch, the boiler does 

not switch on.

3.14 "CHIMNEY SWEEP" FUNCTION.

When activated, this function forces the boiler 

to variable output for 15 minutes.

In this state all adjustments are excluded and 

only the safety thermostat and the limit ther-

mostat remain active. To activate the chimney 

sweep function, press the “Reset” button (2) 

until activation of the function in the absence 

of DHW requests.
Its activation on the boiler display is confirmed 

by the indicators flashing at the same time (11 

and 12 Fig. 2-1), while on the CAR

V2

 (optional) 

it is indicated as “ERR>07”.
This function allows the technician to check the 

combustion parameters. 

Once the function is activated, it is possible to 

select whether to make the chick in CH status 

or DHW status by opening any hot water cock 

and regulating the power by turning the "CH 

regulation" selector (6).

The central heating or DHW operating mode is 
displayed by the relative symbols 

 or 

.

After the checks, deactivate the function switch-

ing the boiler off and then on again.

Attention:

 the boiler needs a certain amount of 

time to stabilise itself before carrying out a com-

bustion parameters check. It is thus necessary to 

wait for the boiler to carry out a self-diagnosis 
test, which is signalled by the (

) flashing 

symbol. Once the symbol stops flashing, it is 

possible to check the combustion parameters.

3.15 PUMP ANTI-BLOCK FUNCTION.

The boiler has a function that starts the pump at 

least once every 24 hours for the duration of 30 

seconds in order to reduce the risk of the pump 

becoming blocked due to prolonged inactivity.

3.16 THREE-WAY ANTI-BLOCK 

FUNCTION.

Both in “domestic hot water” and in “domestic 

hot water-central heating” phase the boiler is 

equipped with a function that starts the three-

way motorised group 24 hours after it was last 

in operation, running it for a full cycle so as to 

reduce the risk of the three-way group becoming 

blocked due to prolonged inactivity.

3.17 RADIATORS ANTIFREEZE 

FUNCTION.

If the system return water is below 4°C, the boiler 

starts up until reaching 42°C.

3.18 P.C.B. PERIODIC SELF-CHECK.

During functioning in central heating mode or 

with boiler in standby, the function activates 

every 18 hours after the last boiler check/power 

supply. In case of functioning in domestic hot wa-

ter mode the self-check starts within 10 minutes 

after the end of the withdrawing in progress, for 

duration of approx. 10 seconds.

N.B.:

 during self-check, the boiler remains off.

Summary of Contents for VICTRIX 24 TT 1E













































Reviews: