background image

1-12

1-13

1-14

1-15

5

4

3

1

2

1

2

3

4

5

6

C

13

C

13

C

13

C

13

13

INS

TALLER

US

ER

MAINTEN

AN

CE TECHNI

CI

AN

The kit includes:

N° 1 -  Gasket (1)

N° 1 -  Concentric bend Ø 60/100 (2)

N° 1 -  Int./exhaust concentric terminal Ø 60/100 (3)

N° 1 -  Internal wall sealing plate (4)

N° 1 -  External wall sealing plate (5)

The adaptor kit includes:

N° 1 -  Gasket (1)

 N° 1  -  Adaptor Ø 80/125 (2)

1.13 CONCENTRIC HORIZONTAL KIT 

INSTALLATION.

Type C configuration, sealed chamber and 

fan assisted.

The position of the terminal (in terms of distanc-

es from openings, overlooking buildings, floor, 

etc.) must be in compliance with the regulations 

in force.
This terminal is connected directly to the outside 

of the building for air intake and flue exhaust. The 

horizontal kit can be installed with the rear, right 

side, left side or front outlet. For installation with 

frontal outlet, one must use the fixing plate and 

a concentric bend coupling in order to ensure 

sufficient space to carry out the tests required 

by law upon commissioning.
•  External grid. Both the Ø 60/100 and Ø 80/125 

intake/exhaust terminal, if properly installed, is 

pleasant to look at on the outside of the build-

ing. Make sure that the external silicone wall 

sealing plate is properly inserted in the wall. 

 

N.B.:

 for proper system operation the terminal 

with grid must be installed correctly ensuring 

that, the “high” indication on the terminal is 

observed during installation.

Horizontal intake-exhaust kit Ø 60/100. 

Kit 

assembly (Fig. 1-12): install the bend with flange 

(2) on the central hole of the boiler, positioning 

gasket (1) with the circular projections down-

wards in contact with the boiler flange, and 

tighten using the screws present in the kit. Fit 

the Ø 60/100 (3) concentric terminal pipe with 

the male side (smooth) to the female side of the 

bend (2) up to the end stop; making sure that the 

internal and external wall sealing plate have been 

fitted, this will ensure sealing and joining of the 

elements making up the kit.
• Extensions for Ø 60/100 horizontal kit (Fig. 

1-13). The kit with this configuration can be 

extended up to a 

max. 12.9 horizontal m

 in-

cluding the terminal with grid and excluding 

the concentric bend leaving the boiler. This 

configuration corresponds to a resistance factor 

of 100. In this case the special extensions must 

be requested.

Immergas also provides a Ø 60/100 simplified 

terminal, which in combination with its ex-

tension kits allows you to reach a maximum 

extension of 11.9 metres.

Horizontal intake-exhaust kit Ø 80/125. 

Kit 

assembly (Fig. 1-14): to install the kit Ø 80/125 

one must use the flanged adapter kit in order 

to install the flue system Ø 80/125. Install the 

flanged adaptor (2) on the central hole of the 

boiler, positioning gasket (1) with the circular 

projections downwards in contact with the boiler 

flange, and tighten using the screws contained in 

the kit. Engage the bend (3) with the male side 

(smooth) to the end stop on the adapter (1). Fit 

the Ø 80/125 (5) concentric terminal pipe with 

the male side (smooth) to the female side of the 

bend (4) (with lip seals) up to the end top; making 

sure that the internal (6) and external wall sealing 

plate (7) have been fitted, this will ensure sealing 

and joining of the elements making up the kit.
• Extensions for horizontal kit Ø 80/125 (Fig. 

1-15). The kit with this configuration can be 

extended up to a 

max. length of 32 m

, includ-

ing the terminal with grid and excluding the 

concentric bend leaving the boiler. If addi-

tional components are assembled, the length 

equivalent to the maximum allowed must be 

subtracted. In this case the special extensions 

must be requested.

The Kit Ø 80/125 includes:

 N° 1  -  Concentric bend Ø 80/125 a 

87° (3)

 N° 1  -  Int./exhaust concentric termi-

nal Ø 80/125 (4)

 N° 1  -  Internal wall sealing plate (5)

 N° 1  -  External wall sealing plate (6)

The remaining kit components must 

not be used

Max. 12900 mm

Max. 12790 mm

Max. 32000 mm

Max. 31956 mm

Summary of Contents for VICTRIX 24 TT 1E













































Reviews: