IMC Networks MediaConverter series Installation Manual Download Page 6

11

LEDs on McPIM TP/FO-VF

The LED functions on 

McPIM TP/FO-VF

are as follows:

A

CTIVITY

Blinks yellow when activity is detected on either port.

TP L

INK

Glows green when link is established on the TP port.

F

IBER

A

LERT

Glows green when 

FiberAlert

is enabled.

FO L

INK

Glows green when link is established on the fiber port.

LEDs on McPIM TP/BNC

The LED function on 

McPIM TP/BNC

is as follows:

TP L

INK

Glows green when link is established on the TP port.

Note

: When removing 

McPIM TP/BNC

from a 

MediaConverter

chassis, use caution

as not to damage the components on the bottom of the board which are shielded.

LEDs on McPIM BNC/FO

The LED functions on 

McPIM BNC/FO

are as follows:

FO L

INK

Glows green when port is enabled.

LEDs on S2MM

The LED function on 

S2MM Module Sets

is follows:

A

CTIVITY

Glows green in normal operation.

RCV

XMT

Fiber Link LED

Twisted Pair Link LED

Activity LED

Twisted Pair  (TP) Link LED

Fiber (FO) Link LED

FiberAlert

LED

Activity LED

ACT

TPLNK

FA

FOLNK

10 Mbps

LEDs on McLIM

The LED functions on 

McLIM

are as follows:

FX L

INK

Glows green when link is established on the FX port.

FX A

CTIVITY

Glows yellow if data is being passed on the FX port.

TX P

AIR

L

INK

Glows green if link is established on the TX port.

TX A

CTIVITY

Glows yellow when data is being passed on the TX port.

General Information

I M C   N

E T W O R K S

T

E C H N I C A L

S

U P P O R T

Phone:

(949) 465-3000 or (800) 624-1070 (in the U.S. and Canada);
+32-16-550880 (Europe)

Fax:

(949) 465-3020

E-Mail:

[email protected]

Web:

www.imcnetworks.com

S

P E C I F I C A T I O N S

Environmental

Operating Temperature:  32° - 104° F (0° - 40° C)
Storage Temperature:  0° - 160° F (-20° - 70° C)
Humidity:  5 - 95% (non-condensing)

Electrical

AC: 100-240 VAC ±10%, 1.2A/0.6A

DC: -48 VDC ±10VDC. 5A

Fiber Optic Specifications

For fiber optic specifications, visit our Web site at

http://www.imcnetworks.com/adocs/fcs.asp

.

F

I B E R

O

P T I C

C

L E A N I N G

G

U I D E L I N E S

Fiber optic transmitters and receivers are extremely susceptible to cont-

amination by particles of dirt or dust which can obstruct the optic path
and cause performance degradation.  Good system performance requires
clean optics and connector ferrules.

1) Use fiber patch cords (or connectors, if you terminate your own

fiber) only from a reputable supplier; low quality components can
cause many hard-to-diagnose problems in an installation.

RCV

XMT

Twisted Pair (TX)

Link LED

Twisted Pair (TX)

Activity LED

Fiber (FX)

Actvity LED

Fiber (FX)

Link LED

12

Summary of Contents for MediaConverter series









Reviews: