background image

ii 

FCC Radio Frequency Interference Statement 

This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules.  

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial 

environment.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 

instruction manual, may cause harmful interference to radio communications.  Operation of this equipment in a residential area is likely to 

cause harmful interference in which the user will be required to correct the interference at his own expense.  

Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. 

The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits.  This digital apparatus does not exceed the Class B 

limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of 

Communications. 

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B 

prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada. 

Warranty 

IMC Networks warrants to the original end-user purchaser that this product, EXCLUSIVE OF SOFTWARE, shall be free 
from defects in materials and workmanship under normal and proper use in accordance with IMC Networks' instructions 
and directions for a period of six (6) years after the original date of purchase.  This warranty is subject to the limitations set 
forth below. 

At its option, IMC Networks will repair or replace at no charge the product which proves to be defective within such 
warranty period.  This limited warranty shall not apply if the IMC Networks product has been damaged by unreasonable 
use, accident, negligence, service or modification by anyone other than an authorized IMC Networks Service Technician 
or by any other causes unrelated to defective materials or workmanship.  Any replaced or repaired products or parts carry 
a ninety (90) day warranty or the remainder of the initial warranty period, whichever is longer. 

To receive in-warranty service, the defective product must be received at IMC Networks no later than the end of the 
warranty period.  The product must be accompanied by proof of purchase, satisfactory to IMC Networks, denoting 
product serial number and purchase date, a written description of the defect and a Return Merchandise Authorization 
(RMA)  number  issued  by IMC  Networks.   No  products  will be  accepted by IMC  Networks  which  do  not  have an RMA 
number.  For an RMA number, contact IMC Networks at PHONE: (800) 624-1070 (in the U.S and Canada) or (949) 465-
3000 or FAX: (949) 465-3020.  The end-user shall return the defective product to IMC Networks, freight, customs and 
handling charges prepaid.  End-user agrees to accept all liability for loss of or damages to the returned product during 
shipment.  IMC Networks shall repair or replace the returned product, at its option, and return the repaired or new 
product to the end-user, freight prepaid, via method to be determined by IMC Networks.  IMC Networks shall not be 
liable for any costs of procurement of substitute goods, loss of profits, or any incidental, consequential, and/or special 
damages of any kind resulting from a breach of any applicable express or implied warranty, breach of any obligation 
arising from breach of warranty, or otherwise with respect to the manufacture and sale of any IMC Networks product, 
whether or not IMC Networks has been advised of the possibility of such loss or damage. 

EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, IMC NETWORKS MAKES NO OTHER WARRANTIES, 
WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS IMC NETWORKS PRODUCT, INCLUDING WITHOUT 
LIMITATION ANY SOFTWARE ASSOCIATED OR INCLUDED.  IMC NETWORKS SHALL DISREGARD AND NOT BE 
BOUND BY ANY REPRESENTATIONS OR WARRANTIES MADE BY ANY OTHER PERSON, INCLUDING EMPLOYEES, 
DISTRIBUTORS, RESELLERS OR DEALERS OF IMC NETWORKS, WHICH ARE 

INCONSISTENT WITH THE WARRANTY SET FORTH ABOVE.  ALL IMPLIED WARRANTIES INCLUDING THOSE OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY LIMITED TO THE DURATION OF THE 
EXPRESS WARRANTY STATED ABOVE. 

Every reasonable effort has been made to ensure that IMC Networks product manuals and promotional materials 
accurately describe IMC Networks product specifications and capabilities at the time of publication.  However, because of 
ongoing improvements and updating of IMC Networks products, IMC Networks cannot guarantee the accuracy of printed 
materials after the date of publication and disclaims liability for changes, errors or omissions. 

 

Summary of Contents for IE-iMcV-MediaLinX TX/SFP

















Reviews: