background image

9

5. Remove the two warning decals (not shown) from

the spa shell. Using a damp cloth, wipe the spa shell
clean. Before filling the spa, make sure that it is
in the desired position and that there is room to
service the spa. Once the spa is filled, it will
have to be drained before it can be moved.

Insert a garden hose into the filter housing, and
begin filling the spa. Do not use soft water. The
spa may be filled with cold water; however, if warm
or hot water is used, the spa will be ready for use
sooner. Fill the spa until the water is at the level of
the molded fill line. Do not overfill the spa.

Refer to the inset drawing. Set the Filter (16),
Cartridge Plug (48), Diverter Plate (33), and Basket
(17) into the filter housing. Next, place the Filter
Cover (8) into the filter housing until it is fully seated.

3. Refer to the drawing on page 6 and locate the long

access opening. Next, locate the two indicated gate
valves inside the opening. Make sure that the gate
valves are open and that the locking clips are
snapped onto the stems of the gate valves (refer to
the inset drawing in step 2 on page 8). 

Make sure that the indicated collars are tightened.

Locate the drain hose inside the opening. Close the
valve knob on top of the drain hose and make sure
that the cap is fully tightened.

4. The hydrotherapy spa operates on a 240-volt power source and must be wired directly to a 40 amp Ground

Fault Circuit Interrupter (GFCI) installed in your home. This procedure must be performed by a qualified
electrician. A wiring diagram is found on the inside of the electronics pack as a reference. Under no
circumstances should the spa be wired by someone other than a qualified electrician. 
Before you
have the spa wired, make sure that it is in the position you want and that it can be easily serviced, if needed.

6. Pull down one of the straps on the Spa Cover (11)

and hold the Buckle (30) against one of the cedar
panels on the spa. (Note: To position the Buckle cor-
rectly, have a second person hold the strap on the
opposite side of the Spa Cover tight.) The Spa
Cover must be tight. Do not place the Buckle
over the grooves between the cedar slats. 
Refer
to the inset drawing. Remove the latch from the
Buckle (30). Attach the Buckle to the cedar panel
with two #4 x 3/4” Screws (31).

Attach the other three Buckles (30) to the cedar pan-
els in the same way.

Remove the Spa Cover (11) from the spa.

5

3

Fill to the
middle of

the

Skimmer

Housing

Filter

Housing

Collars

Collars

Gate

Valve

Electronics Pack

Gate

Valve

6

11

30

Strap

Latch

30

31

8

17

33

48

Drain

Hose

Valve

Knob

Cap

Filter

Housing

16

Strap

Summary of Contents for IMSB63121





















Reviews: