Image Engineering LED-Panel V4 User Manual Download Page 6

Page: 6 / 44

Getting started

1.2 Foreseeable missuse

1.2.1 Older LED-Panel verisons

Most parts of this manual apply to LED-Panel V4. Please contact Image Engineering for the
manual for a previous version of LED-Panel.

1.3 General safety information

Do not

open the device without any instructions from the Image Engineering support and when

connected to the power supply.

1.4 Eye safety

If you use the LED-Panel infrared version please make sure to wear the supplied safety googles

according to

IEC 62471:2009.

Do not

look directly into the emitted light or look through the

optical LED system, this can cause irreversible eye damage.

2 GETTING STARTED

2.1 Scope of delivery

LED-Panel V4, power supply, USB cable, remote control, control software

Optional equipment:

•

iQ-Trigger

•

iQ-Trigger-T

Summary of Contents for LED-Panel V4













































Search results

Summary of Contents for LED-Panel V4

Reviews:

Related manuals for LED-Panel V4

Brands by name

Popular brands

Image Engineering LED-Panel V4, User Manual

Search results

Summary of Contents for LED-Panel V4

Reviews:

Related manuals for LED-Panel V4

Brands by name

Popular brands