ILX Lightwave TSC-599 User Manual Download Page 5

TSC-599

 iii

S

AFETY

 

AND

 W

ARRANTY

 I

NFORMATION

The Safety and Warranty Information section provides details about cautionary 
symbols used in the manual, safety markings used on the instrument, and 
information about the Warranty including Customer Service contact information.

Safety Information and the Manual

Throughout this manual, you will see the words 

Caution and Warning indicating 

potentially dangerous or hazardous situations which, if not avoided, could result in 
death, serious or minor injury, or damage to the product. Specifically:

Caution indicates a potentially hazardous situation which can result in minor or 
moderate injury or damage to the product or equipment. 

Warning indicates a potentially dangerous situation which can result in serious injury or 
death.

WARNING

Visible and/or invisible laser radiation. Avoid direct exposure to the beam.

General Safety Considerations

If any of the following conditions exist, or are even suspected, do not use the 
instrument until safe operation can be verified by trained service personnel:

• Visible damage

• Severe transport stress

• Prolonged storage under adverse conditions

• Failure to perform intended measurements or functions

If necessary, return the instrument to ILX Lightwave, or authorized local ILX 
Lightwave distributor, for service or repair to ensure that safety features are 
maintained (see the contact information on page vii).

All instruments returned to ILX Lightwave are required to have a Return 
Authorization Number assigned by an official representative of ILX Lightwave 
Corporation. See Returning an Instrument on page v for more information.

Summary of Contents for TSC-599

















Reviews: