background image

Edition Notes

Ilumipod 18g2 IP Optic WW User Manual Rev. 4 

Edition Notes 

The  Ilumipod 18g2 IP Optic WW  User Manual Rev. 4  covers the description, safety 
precautions, installation, programming, operation, and maintenance of the Ilumipod 18g2 IP 
Optic WW. ILUMINARC® released this edition of the Ilumipod 18g2 IP Optic WW  User 
Manual Rev. 4 in November 2015. 

Trademarks 

The ILUMINARC® logo, the ILUMINARC® name and all other trademarks in this document 
related to services or products by ILUMINARC® are trademarks owned or licensed by 
ILUMINARC®, its affiliates or subsidiaries. Any other product names, logos, brands, 
company names, trademarks featured or referred to within this document are the property of 
their respective trademark holders. 

Copyright Notice 

The entire content of this document, except where applicable and unless otherwise noted, 
is solely owned by ILUMINARC®, a wholly owned trademark of Chauvet & Sons, 

LLC

© Copyright 2015 ILUMINARC®.  

All rights reserved. 
Electronically published by ILUMINARC® in the United States of America. 

Manual Usage 

ILUMINARC® authorizes its customers to download and print this manual for professional 
information purposes only. ILUMINARC®  expressly prohibits the usage, copy, storage, 
distribution, modification, or printing of this manual or its content for any other purpose 
without its written consent.  

Document Printing 

For better results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. 
If using A4 paper (210 x 297 mm), configure your printer to scale the content of this 
document to A4 paper. 

Intended Audience 

Any person in charge of installing, operating, and/or maintaining the Ilumipod 18g2 IP Optic 
WW  should read all of both the guide that shipped with it and this User Manual before 
installing, operating, or maintaining this product. 

Disclaimer 

ILUMINARC® believes that the information contained in this manual is accurate in all 
respects. However, ILUMINARC® assumes no responsibility for any error or omissions in 
this document. ILUMINARC® reserves the right to revise this document and to make changes 
from time to time in the content hereof without obligation of ILUMINARC® to notify any 
person or company of such revision or changes. This does not constitute in any way a 
commitment by ILUMINARC® to make such changes. ILUMINARC® may issue a revision 
of this manual or a new edition of it to incorporate such changes. 

Document Revision 

The Ilumipod 18g2 IP Optic WW User Manual Rev. 4 supersedes all previous versions of this 
manual. Replace any previous versions of this manual with this version. 

Author 

Date 

Editor 

Date 

D. Couppe

5/1/15 

Summary of Contents for Ilumipod 18g2 IP Optic RGB
























Reviews: