Ilumenite ILDW-7045524-00D-11 User Manual Download Page 3

1.  Introduction 

Welcome to using the high power LED washer of Neo-Neon. The light takes the high power LED technology, with 

long lifespan and high IP rating. It has the high power red, matched with the green and blue balanced. It can make all 

kinds of vivid illumination effects, along with DMX receiving and auto mode. The operation interface is easy to 

operate and user-friendly, which is achieved by key and 5*7LED matrix. It is suitable for the entertainment, 

decorative, architecture illumination industry. 

z

 

Main Functions: 

  R,G,B mixed colors and can make all kinds of colors   

* 

Adjust the brightness linearly   

* 

The adjustable strobe effect 

* 

The prefabricated colors and the “rainbow” effect 

* 

Install all kinds of specification by hand 

* 

Show the function of 180 degrees overturning 

* 

English manual system an the adjustable brightness of the digital displaying tube 

* 

The safeguarding function of over-heat   

* 

Auto Test Mode   

* 

Record the running time of the different colorful LED 

* 

Record the total running time of the fixture 

* 

Can edit three pieces of programs, 10 acts of each program for maximum   

* 

Can edit 36 pieces of time events, each event can randomly install the running start and end time of the 

included programs.   

 

z

 

The approaches to controlling

 

 

* 

DMX-512  

* 

Run alone through installing the inner programs 

* 

Install the independent running programs for everyday during one week 

* 

Drive 30 pieces of fixtures through the Master/Slave mode 

* 

Install the DMX address of the fixture

 

 

z

 

Configuration: 

    45 pieces of 3 in 1---3W LED 

 

z

 

Angle: 

 

*  The adjustable angle for single head: 

0

°---180°

 

*  The angle of the lens  

25

°

 

*  Other angles available :10°、40°、60° 

 

 

 

2

Technical Specification 

 

Page   23   of  36

Summary of Contents for ILDW-7045524-00D-11














Reviews: