Save your own settings to presets
_
1
_
~
_
8
_
and use them
instantaneously when jamming.
(1) Turn the rotary encoder in the center to choose the effect
model of your choice.
(2) Adjust the 4 knobs above to create the perfect sound.
(3) Push down on the rotary switch for 2 seconds
and the LED will start to blink.
(4) Turn the rotary encoder to any of the preset position
_
1
_
~
_
8
_
.
(5) Press the rotary switch again and the current sound will be
saved in the selected position.
(6) Use
_
PRESET
_
↑ /
_
PRESET
_
↓ switch to shuffle through and
activate the preset of your choice.
※ On pressing
_
PRESET
_
↑ /
_
PRESET
_
↓
switch,
The
_
PRESET
_
LED on the bottom left face will light up
to indicate that you are in the preset mode.
※ The preset positions of
_
1
_
~
_
8
_
are independent from
the effect models written next to them. That is, you can save
any effect model to any preset number that you want.
Powering on
with
_
PRESET
_
pedal engaged
will let you
modify the pedal mode. The unit will cycle through the above
settings. The initial setting is at
_
2
_
. While
_
PRESET
_
pedal stays
down, the LED will light up among
_
1
_
_
2
_
to indicate the
current mode.
-
_
PRESET
_
↑
Functions as a preset-up switch.
Every press will change the current
preset
_
1
_
~
_
8
_
in increasing order.
-
_
PRESET
_
↓
Functions as a preset-down switch.
Every press will change the current
preset
_
1
_
~
_
8
_
in decreasing order.
-
TAP
Functions as a tap time switch.
The interval between two consecutive
taps will set the
.
No.
_
PRESET
_
_
1
_
_
PRESET
_
↑
_
PRESET
_
↓
_
2
_
_
PRESET
_
↑
TAP
-
Changes the modulation speed/rate.
Clockwise direction increases the speed.
The LED on the left blinks to indicate the modulation time.
-
Sets the depth and width of the modulation effect.
At 5 o'clock, the effect will show the largest variation.
-
Depending on the effect model, this will adjust the intensity
of the feedback/emphasis/waveform.
Exceptions that are not affected by this knob are:
,
,
.
-
Adjusts the balance between the level of the modulation
effect and the original signal. Pointed straight up
at 12 o'clock sets an equal ratio of 1:1.
The
connector can accommodate an
external switch or expression/volume
pedal. Make sure to turn off the power
before connecting an external pedal.
Depending on the maker of the pedal,
the polarity may be different, so please
check beforehand for compatibility.
-
Switch Pedal
: Can be set to
TAP
switch
or
_
PRESET
_
↑
switch.
Please refer to
“Changing Pedal Mode”
.
-
Expression/Volume Pedal
: With this,
you can adjust a selected parameter,
one of the 4 control knobs.
Please refer to
“Choosing an EXP Parameter”
.
If you power the unit up while pushing down on the central rotary switch, this
will allow you to change
setting. You can map the expression/volume pedal
to one of the 4 control knobs. The unit will cycle through the controls as long
as the rotary switch remains pressed, with the LED
_
3
_
_
4
_
_
5
_
_
6
_
indicating
the selection of each of the corresponding knobs. Let go when the desired
parameter is selected.
※ This is only for when you have an expression/volume pedal to
connector.
Select the desired effect with the rotary encoder in the center.
-
A chorus effect that brings a warm abundance.
-
A vintage flanger that reminds you of a jet fighter.
-
This effect reproduces the unique and wonderful
sound of a rotating leslie speaker.
-
Adds some originality to your jam with
the odd sensation brought on by off-sync phases.
-
A soft and slow filter that will make you feel
the sense of “wah-wah”.
-
Panning between left and right makes its mark
especially when you're playing chords.
-
From a vintage tube tremolo to a modern FET tremolo,
try them all by turning the
knob.
-
Just the right amount of pitch vibrato will bring
liveliness to your tones.
The switch on the right lets you select the bypass mode of your choice.
-
The signal passes as if there was nothing on the way.
-
Provides a low impedance buffer bypass.
Switch Pedal
Tip
Signal
Sleeve
Ground
※ When switch is engaged,
Tip and Sleeve are in contact.
Tip
Signal
Ring
Voltage
Sleeve
Ground
-
Turns the effect on and off.
When the LED is lit up, the effect is functioning,
and when it is off, you are in bypass mode.
-
_
PRESET
_
Functions as a preset-up
_
PRESET
_
↑
switch.
Every press will change the current preset
_
1
_
~
_
8
_
in increasing order.