background image

3

Fans are UL/CUL Listed, Standard 705.

1. Do not depend on any switch as the sole means of disconnecting

power when installing or servicing the fan.

2. Always disconnect, lock-out, and tag-out power source before installing

or servicing. Failure to disconnect power source can result in fire, shock,

or serious injury.

3. Motor will restart without warning after thermal protector trips. Do not

touch operating motor; it may be hot enough to cause injury.

4. Do not place body parts or objects in fan or motor openings while motor

is connected to the power source.

5. All electrical connections should be made by a qualified electrician.

6. These utility exhaust fans are for general purpose exhaust applications

only. Do not use these exhaust fans in an area where corrosive or

explosive materials may be found.

7. Follow all local and state/provincial electrical and safety codes in the

United States and Canada, as well as the National Electrical Code (NEC)

and the Occupational Safety and Health Act (OSHA) in the United States,

and the Canadian Electric Code (CEC) in Canada.

8. Always disconnect power source before working on or near a motor or its

connected load.

9. Protect the power cable from coming in contact with sharp objects.

10. Do not kink or create tight bends in the power cable and never allow the

cable to come in contact with oil, grease, hot surfaces, or chemicals.

11. Make certain that the power source conforms to the requirements of

your specific exhaust fan model. The fan frame and motor must be

electrically grounded to a suitable electrical ground, such as a grounded

water pipe or ground wire system.

12. To reduce the risk of injury to persons, please observe the following:

In the United States, OSHA compliant guards are required when fan is

installed within 7 feet of the floor or working level. In Canada, CSA

compliant guards are required when fan is installed below 2.5 meters

(8.2 feet) above the floor or grade level.

13. Questions? Please contact our service center by calling 1-800-317-

1688.

GENERAL SAFETY INSTRUCTIONS

Summary of Contents for ILG8SF10V










Reviews: