background image

AC + DUAL USB WALL PLATE COVER

User’s Guide for  Model IAWP28-2115-01

Step 2: Remove the Existing Face Cover

•  Using a flat head screwdriver, remove the existing wall plate. Turn the 

screwdriver counter-clockwise to remove the screw. After removing 

the old wall plate and you will see that the outlet is mounted in the 

electrical box in the wall. Remove the bottom screw of the outlet.

Step 3: Install AC + Dual USB Wall Plate Cover

•  Line up the two large outlet holes of the AC + Dual USB Wall Plate 

Cover over the two raised sockets of the exposed outlet and place the 

AC + Dual USB Wall Plate Cover over the outlet. Ensure the two metal 

contacts on the back of the AC + Dual USB Wall Plate Cover are aligned 

with the metal contacts on the sides of the electrical outlet. Install the 

short white screw provided with the wall plate in the center hole, to 

attach the wall plate to the outlet. Now, install the long white screw 

through the lower hole in the AC + Dual USB Wall Plate Cover. Turn the 

screwdriver clockwise to tighten the lower screw, which will pull the 

wall plate firmly against the wall.

Introduction 

Thank you for purchasing this product! This AC + Dual USB Wall Plate Cover 

is the easiest way to add USB fast-charging capability to 15 Amp standard 

Duplex electrical outlets in a home or office.

The AC + Dual USB Wall Plate Cover connects to a 15 Amp standard Duplex 

outlet and provides 2 USB charging ports without using an electrical outlet. 

The total output for the USB ports is 3.1A. If you are using one USB port, it will 

provide 2.1A, the other will provide 1A.

Please follow these directions carefully to safely install this product.

Caution 

It is critical to confirm that power has been shut off from the fuse panel or 

circuit breaker box to the designated outlet before starting the replacement. 

Test the outlet with a voltage meter prior to the installation of the wall plate 

to ensure that power has been disconnected.

You will need a flat head screwdriver for this installation.

Installation 

Installing this AC + Dual USB Wall Plate Cover takes 3 simple steps:

Step 1: Turn Off The Power

•  Locate the electrical cut off point (breaker panel, fuse panel, etc.) of the 

designated outlet. Turn off the breaker switch or remove the fuse.

•  Hint: It may help to plug in a light or similar device to the outlet and 

turn it on. When you have found the correct breaker or fuse, the light 

will go out. Additionally, test the outlet with a voltage meter capable of 

making the proper readings prior to the installation of the wall plate to 

ensure power has been disconnected.

Cleaning 

•  Clean the charger with a soft, 

dry cloth. 

•  If mild detergents are needed 

to clean tougher spots, shut off 

the outlet from the fuse panel 

or circuit breaker box and make 

sure that no moisture gets inside 

the USB ports or outlet on the 

front of the unit.

FCC Warning

Changes or modifications to this unit not expressly approved by the party 

responsible for compliance could void the user’s authority to operate the 

equipment.
NOTE: This equipment has been tested and found to comply with the limits 

for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against harmful interference 

in a residential installation. This equipment generates, uses, and can radiate 

radio frequency energy and, if not installed and used in accordance with 

the instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or 

more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Do not remove the outlet’s 

wall plate until you are certain 

that the outlet is not live. 

Exposed, live 12–volt AC 

devices such as wall outlets 

and light switches can cause 

severe injury, even death.

•  After confirming that the installation is correct, switch the fuse or 

breaker switch back on to restore power to the outlet.

•  Congratulations! You’ve finished the installation and may begin using 

the outlet to charge devices with the USB ports.

Remove the bottom screw

WARNING: This product can expose you to chemicals including lead, 
which is known to the State of California to cause cancer and birth 
defects or other reproductive harm. For more information go to www.
P65Warnings.ca.gov. This product meets and complies with all 

Federal regulations.

Safety Warnings

•  WARNING: To prevent fire or shock hazards, do not expose this unit to 

rain or moisture.

Short screw

Long screw

It may be necessary 

to adjust the contact 

screws to properly 

fit the contacts on 

the plate cover. 

BE ABSOLUTELY 

SURE THE PLUG IS 

NOT LIVE BEFORE 

TOUCHING THE 

SOCKET OR 

MAKING THE 

ADJUSTMENT.

Reviews:

Related manuals for IAWP28-2115-01