6
CClloossiinngg tthhee H
Hoouussiinngg
1. Place housing face down.
2. Check to see that there is an o’ring
on the housing back and that it is
clean and in its proper location.
3. Some control shafts can be slid out,
making camera installition easier.
Gently pull out on a control until it
stops.
4. Guide the back onto the housing.
The o’ring should touch the
housing all the way around. There
should be an even gap all the way
around between the housing and
the housing back.
5. Lift the lid snaps so they are
extended and place the lid snap
into the hook on the housing back.
6. To close the housing push
down on the lid snaps until
they snap into place . Lid
snaps on opposite sides of the
housing should be closed at the
same time. Be sure they are down
far enough to engage the lock.
DDoouubbllee cchheecckk - Once the housing is closed, check the o’ring seal.
Check the gap between the housing back and the housing, it
should be even all the way around.
Look through the clear plastic back at the o’ring. You should see a
darkened area where the o’ring is compressed against the
housing back. If you do not see an even black compression seal
all the way around the back, open the lid snaps, reseat the
housing back and close the lid snaps. Visually check the seal again.
o’ring
housing back
housing back
housing
housing
o’ring
even gap
all 4 sides
5
External TTL Strobe Connector
Waterproof Cap
O'ring
Housing Back
Hot Shoe
Connector
Camera
FFllaasshh CCoonnnneeccttiioonn ffoorr EExxtteerrnnaall SSttrroobbeess
When using an external strobe connect the housings Hot Shoe
Connector, slide the connector into the hot shoe of the camera
from the back of the camera as shown. Slide the connector
forward until it stops. This can be done after the camera is
secured with the mounting bolt.
N
NOOTTEE:: Even if you are not using an external strobe it is
recommended that you slide the housings Hot Shoe Connector
into the camera's hot shoe. In this position it is less likely to
interfere with the o'ring seal.
CCaauuttiioonn::
Do not remove the
External Strobe
Connector’s
waterproof cap
unless an external
sync cord is going
to be plugged in.
U
Ussiinngg FFllaasshh
The camera's built-in flash cannot be used. To use flash an
external flash must be connected to the housing.
7
CChheecckkiinngg CCoonnttrroollss
Once the housing has been closed, push the controls back into
place. Make sure they line up with the camera’s controls.
ZZoooom
m CCoonnttrrooll
(NOTE:) After you have used the
housing’s zoom control it must be
returned to the center position to
disengage. If the housing zoom
control is pushing the camera
zoom lever in either direction you
cannot take a picture or access
any other function as the camera
is receiving a signal from the
engaged zoom control.
TTuurrnn CCaam
meerraa O
Onn
Turn the camera on and operate each of the housing controls to
get a feel for using the camera in the housing. Take a few
pictures above water with the camera in the housing.
Zoom control
engaged
Zoom control
disengaged
(centered)
LLeennss PPoorrtt
Treat the glass in the lens port as a camera lens. After use, rinse
and gently dry the lens port to avoid water spotting. To clean
use a mild soap solution or lens cleaner.
Do not use alcohol or window cleaner on the Lens Port.
CCaauuttiioonn
When the camera is in the housing and the lens is fully extended
the lens almost touches the inside of the housing's port.
RReem
moovvee aannyy aacccceessssoorryy lleennss aattttaacchhm
meennttss ssuucchh aass ffiilltteerrss bbeeffoorree
iinnssttaalllliinngg tthhee ccaam
meerraa iinnttoo tthhee hhoouussiinngg.. Any attachment that
adds length to the lens will restrict the zoom and may scratch
the inside of the housings port.
8
O
Oppttiioonnaall AAcccceessssoorriieess
EExxtteerrnnaall SSuubbssttrroobbeess
External strobes offer several advantages over using the
camera’s built-in flash. External strobes move the flash away
from the camera lens which helps reduce backscatter. They also
expand lighting options to achieve the best lighting for
different subjects and lenses. A strobe such as the DS51 is ideal
for use with macro and most standard camera lenses up to
28mm. When an optional wide angle lens is added a strobe such
as the DS125 is needed as it has a greater angle-of-coverage. A
second external strobe can be added to fill the shadows and
produce more realistic photographs.
TTTTLL EExxppoossuurree M
Mooddee
Ikelite DS Substrobes are fully TTL functional and provide real
Olympus TTL control with this housing. For TTL exposure you
must use an Ikelite DS Substrobe and the Ikelite #4103.51 sync
cord or #4103.52 dual sync cord for dual strobes.
N
NO
OTTEE:: Refer to camera manual for camera flash settings when
using an external strobe.
M
Maannuuaall EExxppoossuurree M
Mooddee
This camera can be used with the Ikelite Substrobe, DS51, 100A,
DS125, or 200 in the manual mode. A #4103.51 sync cord is
required to connect the Substrobe to the housing.
M
Maannuuaall EExxppoossuurree M
Mooddee 22
Use the Ikelite EV-Controller with a DS Substrobe for more
control over manual exposure. The EV Controller provides 10
manual power settings in 1/2 stop increments. For housings with
an external sync cord connection it is recommeded to connect the
EV-Controller to the housing with a #4103.51 sync cord.
All manuals and user guides at all-guides.com
