IIM
MAAGGEE RREEVVEERRSSIIN
NGG CCIIRRCCUUIITT
____________________________________________________________________________________________________
The image reversing circuit is mounted inside the housing. The circuit reverses
(flips) the image and words on the LCD screen so that when the image is reflected
in the external mirror, it appears correct left-to-right.
Secure the camera to the tray and partially slide the camera and tray inside the
housing so you can then connect the cable from the reversing circuit to the A/V Out
port on the camera. The reversing circuit will automatically turn ON when connected
to the camera and the camera is ON; the image and words in the LCD screen will
appear in reverse.
OOnn//OOffff SSw
wiittcchh
An on/off switch is featured on the reversing circuit. Use the reversing circuit
control on the housing to access the on/off switch on the circuit. The circuit will
automatically turn ON when connected to the camera and the camera is ON.
When turning the camera OFF, there is a 5-minute standby power down delay
on the camera that occurs when the reversing circuit is ON during power down.
Therefore to avoid the 5-minute power down delay, turn the camera OFF and also
turn the circuit OFF to power down the camera immediately.
FFuunnccttiioonnss LLoocckkeedd OOuutt
When the reversing circuit is ON, some camera functions may be locked out. To
correct for such a problem, temporarily turn the circuit OFF, change the function on
the camera, and then turn the circuit back ON.
The camera’s Microphone is also disabled when the reversing circuit is on.
FFIIN
NAALL PPRREEPPAARRAATTIIOON
N
__________________________________________________________________________________________________________________
Remove the lens cap and cord from the camera.
Otherwise, they may interfere
with the housing seal.
The camera's auto focus feature is utilized underwater. For best results, move in
close to your subject and use the wide angle range to shoot thru as little water as
possible. The full zoom range is accessible underwater.
Turn the camera’s built-in flash OFF.
Chart shows recommended initial settings
underwater.
W
WH
HIITTEE BBAALLAAN
NCCEE
__________________________________________________________________________________________________________________________
Initially set the white balance to Auto. Use the touch screen controls on the
housing to change white balance.
CCoolloorr FFiilltteerr:: When using the color filter (during the day), set camera white balance
to Indoor for 0-15 foot depth. For 15-80 foot depth, set white balance to Outdoor.
VViiddeeoo--LLiittee:: When using optional Video Lite at NIGHT, set the camera white balance
to the Indoor position. During the DAY, use the Outdoor setting for subjects beyond
4-5 feet and the Indoor setting for closer subjects.
CCAAM
MEERRAA
SSEETTTTIIN
NGG
Power On/Off
– Camera (On)
Zoom Lever
– Wide Angle Setting
Focus
– Auto Mode
Exposure
– Auto Mode
Program AE
– Auto Mode
Shutter Speed
– 1/60 Normal
White Balance
– Auto Mode (see section)
Steady Shot
– Off
Built-in Flash
– Off
I
I N
N SS TT AA LL LL AA TT II OO N
N
CCAAM
MEERRAA TTRRAAYY
________________________________________________________________________________________________________________________________
The camera mounts to the tray, which extends from the back plate of the
housing. DDOO N
NOOTT remove the tray from the back plate.
Position the camera against the two stabilizing
pins on the tray and secure with the camera
mounting bolt. The camera should fit easily on the
tray and should be parallel with the sides of the tray.
The lens shade must be threaded completely into
the camera lens to avoid clearance or sealing problems.
Extend the camera’s viewfinder back toward
the SuperEye.
IIN
NSSEERRTTIIN
NGG TTH
HEE CCAAM
MEERRAA
__________________________________________________________________________________________________________
Check that the o’ring is clean and properly positioned on the lip of the clear
housing back plate. Check that the lens shade is completely threaded into the camera.
Once the camera is mounted to the tray as shown above, pull the housing
controls out to provide clearance for installing the camera. Partially slide the camera
into the housing so you can connect the reversing circuit cable to the A/V Out port
on the camera. When sliding the camera into the housing align the housings zoom
control to accept the camera’s zoom lever. Make sure the lens shade on the front of
the camera fits into the port recess in the front of the housing.
DDOO N
NOOTT force this installation; the camera and tray should slide easily into place
so the housings back plate o’ring is resting against the main housing body. In this
position the lid snaps can be positioned over the lid hooks on the housing back plate
and snapped into position to seal the housing.
H
HOOUUSSIIN
NGG CCOON
NTTRROOLLSS
________________________________________________________________________________________________________________
Slide the housing controls back in place making sure they properly align with the
camera functions.
Operate each control to see how it works with the camera. Some controls such
as start/stop will be used frequently. Other controls may seldom be utilized. Refer to
your camera owner's manual for the proper function of each camera control. Look
thru the back to be sure that you can see into the viewfinder.
When using the housing controls, especially the start/stop, do NOT use excessive force
because you could damage the camera.
CCAAUUTTIIOON
N
Remove the lens cap and cord from the camera. Otherwise, the cord may
interfere with the housing seal.
If the housing controls are not properly positioned, they could interfere with the housing seal.
M
MAAN
NUUAALL FFOOCCUUSS OOPPEERRAATTIIOON
N
______________________________________________________________________________________________
Manual focus may be preferred in low light levels or when the subject possesses
little contrast. Set the focus switch to Manual to cancel the auto focus. If you want
to manually adjust the focus, rotate the manual focus control as desired.
To reactivate the auto focus, set the focus switch to Auto.
IIKKEELLIITTEE UUN
NDDEERRW
WAATTEERR SSYYSSTTEEM
MSS
50 West 33rd Street • PO Box 88100 • Indianapolis, IN 46208 USA • 317.923.4523
Email: [email protected]
•
www.ikelite.com
6038.91-01-0907
Camera Mounting Bolt
Camera Tray
O’ring
Back Plate
Internal Lens Shade
Stabilizing
Pins
All manuals and user guides at all-guides.com
