12
Safety instructions
ō0DNHFHUWDLQWKDWWKHXQLWLVVHWDWWKHORZHVW
speed before commissioning; otherwise, the
unit will begin running at the speed last set.
Gradually increase the speed.
ō5HGXFHWKHVSHHGLIWKHPHGLXPVSODVKHVRXWRI
the vessel because the speed is too high.
ō%HIRUHVZLWFKLQJRQWKHGLVSHUVLQJLQVWUXPHQW
make sure that its shaft is immersed min. 45
mm in the medium to prevent the medium
from splashing out.
ō7KHGLVWDQFHEHWZHHQWKHGLVSHUVLRQWRRODQG
the vessel bottom should not be less than 10
mm (fi g. 1).
ō(QVXUHWKDWWKHVWDQGGRHVQRWVWDUWWRPRYH
ō
In the event of unbalance or unusual noises,
switch off the appliance immediately. Replace
the dispersing element. If there is no difference
after the change of the dispersing tool, return it
to the dealer or the manufacturer along with a
description of the fault.
ō'RQRWWRXFKURWDWLQJSDUWVGXULQJRSHUDWLRQ
ō
Caution: Burns hazard!
When in operation,
the dispersing element and the coupling fl ange
can become hot.
ō'RQRWFRYHUWKHYHQWLODWLRQVORWVRQWKHGULYHLQ
order to ensure adequate cooling of the drive.
ō'RQRWSURFHVVDQ\ĠDPPDEOHRUFRPEXVWLEOH
materials.
ō 3URFHVV SDWKRJHQLF PDWHULDOV RQO\ LQ FORVHG
vessels under a suitable extractor hood. Please
contact
IKA
®
if you have any questions.
ō 'R QRW RSHUDWH WKH DSSOLDQFH LQ H[SORVLYH DW
mospheres, with hazardous substances or un-
der water.
ō7KHUHPD\EHHOHFWURVWDWLFGLVFKDUJHVEHWZHHQ
the medium and the dispersing instrument
shaft which could pose a direct danger.
ō2QO\SURFHVVPHGLDWKDWZLOOQRWUHDFWGDQJH
rously to the extra energy produced through
processing. This also applies to any extra ener-
gy produced in other ways, e.g. through light
irradiation.
ō0HWHUSRZGHUQRWWRRFORVHWRWKHĠDQJH3RZ
der can be blown away by air turbulences of
the drive.
ō
Safe operation is only guaranteed with the ac-
cessories described in the ”Accessories” chapter.
ō $OZD\V GLVFRQQHFW WKH SOXJ EHIRUH ğWWLQJ DF
cessories.
ō7KHDSSOLDQFHFDQRQO\EHGLVFRQQHFWHGIURP
the mains supply by pulling out the mains plug
or the connector plug.
For your protection
ō
Read the operating instructions in full be-
fore starting up and follow the safety ins-
tructions.
ō.HHSWKHRSHUDWLQJLQVWUXFWLRQVLQDSODFHZKH
re they can be accessed by everyone.
ō(QVXUHWKDWRQO\WUDLQHGVWDIIZRUNZLWKWKHDS
pliance.
ō)ROORZWKHVDIHW\LQVWUXFWLRQVJXLGHOLQHVRFFX
pational health and safety and accident preven-
tion regulations.
ō :HDU \RXU SHUVRQDO SURWHFWLYH HTXLSPHQW LQ
accordance with the hazard category of the
media to be processed. Otherwise there is a
risk from:
- splashing and evaporation of liquids
- body parts, hair, clothing and jewellery get-
ting caught.
ō6HWXSWKHVWDQGLQDVSDFLRXVDUHDRQDQHYHQ
stable, clean, non-slip, dry and fireproof sur-
face.
ō &KHFN WKH DSSOLDQFH DQG DFFHVVRULHV EHIRUH
hand for damage each time you use them. Do
not use damaged components.
ō7KHDSSOLDQFHLVQRWVXLWDEOHIRUPDQXDORSH
ration.
ō7KHDJLWDWLRQYHVVHOVXVHGIRUGLVSHUVLQJKDYH
to be secured. Consider on a good stability of
the entire structure.
ō6HFXUHWKHDJLWDWLRQYHVVHODJDLQVWWZLVWLQJ
ō &KHFN WKDW WKH WXUQLQJ NQREV DUH VHFXUH DQG
tighten if necessary.
ō *ODVV YHVVHOV PXVW DOZD\V EH VHFXUHG ZLWK D
clamp to prevent them spinning. When wor-
king with flasks elastic couplers must be used
to prevent fracture of the glass.
ō1RWHWKHRSHUDWLQJLQVWUXFWLRQVRIWKHGLVSHU
sing tool and accessories.
ō 2QO\ GLVSHUVLQJ HOHPHQWV DSSURYHG E\
IKA
®
may be used.
ō3OHDVHREVHUYHWKHSHUPLWWHGVSHHGIRUWKHGLV
persing element. Never set higher speeds.
ō'RQRWXVHWKHDSSOLDQFHZLWKRXWDGLVSHUVLQJ
element.
ō8VHWKHGLVSHUVLQJWRRODOZD\VLQVLGHWKHVWLUULQJ
vessel.
ō 1HYHU UXQ GLVSHUVLRQ WRROV GU\ DV WKH JDVNHW
and bearings will be destroyed if the tools are
not cooled by the medium.
ō
Caution: Burns hazard!
If a dispersing element
is not inserted into the drive fl ange as far as the
mark it can become extremely hot in operation
and thus suffer damage.
DANGER!
