Iiyama Prolite E433 User Manual Download Page 2

FCC DECLARATION OF CONFORMITY

Model Number:

PLE433

Trade Name:

iiyama

Responsible party:

IIYAMA North America, Inc.

Address:

165 West Street Road, Suite 101B,Warminster,PA18974  U.S.A.

Telephone number:

215-682-9050

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for Class B Personal Computers and
peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the device is operated in a residential environment. This device generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If you determine the device does cause harmful interference to radio or
television reception (this may be determined by monitoring the interference while turning the device off and
on), you are encouraged to try to correct the interference by one of the following measures:

„

Reorient or relocate the receiving antenna.

„

Increase the separation between the device and receiver.

„

Connect the device into an outlet on a circuit different from that to which the receiver
is connected.

„

Consult the dealer or an experienced radio or TV technician for help.

To meet the FCC requirements, you should use a signal cable with ferrite core at both ends.

CAUTION

Changes or modifications not expressly approved by iiyama could void the users authority
to operate the device under FCC compliance regulations.

CE MARKING DECLARATION OF CONFORMITY

This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/

EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas,
business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
All places of operation are characterised by their connection to the public low voltage power supply system.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as
set out in the radio interference regulation of the Canadian department of communications.

CANADIAN DEPARTMENT OF COMMUNICATIONS  COMPLIANCE
STATEMENT

„

We reserve the right to change specifications without notice.

„

All trademarks used in this user manual are the property of their respective owners.

„

As an E

NERGY

 S

TAR

® 

Partner, iiyama has determined that this product meets the E

NERGY

 S

TAR

® 

guidelines for

energy efficiency.

PLE433-content.P65

2004/03/24, 15:09

Page 2

Adobe PageMaker 7.0J/Win

Summary of Contents for Prolite E433
















Reviews: