background image

Figure 1 - Remote Control Battery Compartment

MODE

    BATTERY

COMPARTMENT

BACK

FRONT

SET

PROG

PROG MODE

SET

TSRC TOUCHSCREEN REMOTE CONTROL KIT

[FOR USE WITH MODELS ALPHA32/36, GAMMA26, BLAZE&GLOW18/24, MAGNIFLAME24/30, MULTI-SIDED27 NORTHERNOAK27, DUAL-FLAME EOS18, SHERIDAN18/24, 
RIOLIGHTS24/30, VRT4032/36, VCT4032/36, VCM3026, CIS VF, GLOW-RAMP BGE18/24, MULTI-SIDED FVFM27, VF18/24, DUAL BURNER VD1824, ODYSSEY36/42, 
VRE3036/42, CHELSEA21, CONCORD26]

TSRC TOUCHSCREEN 

REMOTE CONTROL KIT

P/N 127160-01
Rev. B, 04/2017

HEARTH PRODUCTS

KITS AND ACCESSORIES

The transmitter operates with (4) AAA 1.5V batteries that are included. 
Install the batteries supplied with the unit into the battery compartment. 
It is recommended that ALKALINE batteries always be used for this 
product. 

Be sure the batteries are installed with the (+) and (-) ends 

facing the correct direction.

When you start up the remote, if a low battery signal appears or if they 
LCD screen does not illuminate when you touch it, check battery posi-
tion and if the batteries are fully charged.

Cat. No.

Model

Description

F1079

TSRC

Receiver & Touchscreen Remote Kit

KIT CONTENTS

1 ea. Remote Control
4 ea. AA 1.5 volt batteries (for receiver)
4 ea. 1 ea. Instruction Sheet

REQUIRED TOOLS AND SUPPLIES

Flat Blade Screwdriver

GENERAL INFORMATION

The hand-held touchscreen remote control allows the fi replace to 
be operated in a manually or thermostatically controlled mode. 

READ ALL THE STEPS BEFORE STARTING THE INSTALLATION

THE APPLIANCE MUST BE OFF AND COLD BEFORE BEGINNING.

ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE 
INSTALLATION AND OPERATION MANUAL PROVIDED WITH THE 
APPLIANCE APPLY TO THESE INSTRUCTIONS.

If you encounter any problems, need clarifi cation of these instructions
or are not qualifi ed to properly install this kit, contact you local 
distributor or dealer.

If any of these parts are missing or damaged, contact your dealer or 
IHP.us.com for referral information.

INTRODUCTION 

This remote control system was developed to provide a safe, reliable, 
and user-friendly remote control system for gas heating appliances or 
other compatible appliances. The system can be operated manually 
from the transmitter.

IHP.us.com

1

MODE

SET

PROG

f i r e - p a r t s . c o m

Summary of Contents for TSRC









Reviews: