background image

FCC Statement

This device complies with part 15 of FCC Rules. Operation 

is subject to the following two conditions: (1) this device 

may not cause harmful interference, and (2) this device must 

accept any interference received, including interference 

that may cause undesired operation. This equipment has 

been tested and found to comply with the limits for a Class 

B digital device, pursuant to part 15 of FCC Rules. These 

limits are designed to provide reasonable protection against 

harmful interference when the equipment is operated in a 

residential installation. This equipment generates, uses, and 

can radiate radio frequency energy and, if not installed and 

used in accordance with the instruction guide, may cause 

harmful interference to radio communications. However, 

there is no guarantee that interference will not occur in a 

particular installation.  If this equipment does cause harmful 

interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more 

of the following measures:

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and 

• 

the receiver.
Connect the equipment into an outlet on a circuit 

• 

different from that to which the receiver is connected.

Consult a service representative for help.
Properly shielded and grounded cables and connectors 

must be used in order to comply with FCC emission limits. 

LifeWorks is not responsible for any radio or television 

interference caused by using other than recommended 

cables and connectors or by unauthorized changes or 

modifications to this equipment. Unauthorized changes or 

modifications could void the user’s authority to operate the 

equipment. 
Responsible party:
LifeWorks Technology Group LLC 

1412 Broadway

 

New York, NY 10018

Tested To Comply With FCC Standards 

FOR HOME OR OFFICE USE

Warning

Improper setup, use and care of this product can increase 

the risk of serious injury, death or device damage. Read 

and keep this guide and all other printed guides for future 

reference. For updated guides or replacements, go to 

www.life-works.com

Do Not Attempt Repairs

Do not attempt to take apart, open, repair, service or 

modify the device(s). Doing so may risk electric shock or 

other hazard. Evidence of any attempt to open or modify 

the device, including any peeling, puncture or removal of 

labels, will void the Limited Lifetime Warranty.

Summary of Contents for MYLIFE IH-W355NB













Reviews: