manualshive.com logo in svg

iHealth KD-557BT, Owner'S Manual, Page: 6 / 17

Share
Download
iHealth KD-557BT Owner'S Manual Download Page 6

 

 

第

 5 

页

 

共

 16

页

Note:  

a.Please refer to the cuff circumference range in “SPECIFICATIONS” to make sure that the 

appropriate cuff is used. 

b.Measure on the same arm each time. 

c.Do not move your arm, body, or the monitor and do not move the rubber tube during measurement. 

d.Stay still, calm for 5 minutes before blood pressure measurement. 

e.Please keep the cuff clean. If the cuff becomes dirty, remove it from the monitor and clear it by hand 

in a mild detergent, then rinse it thoroughly in cold water. Never dry the cuff in clothes dryer or iron it. 

Clean the cuff after the usage of every 200 times is recommended. 

 

  TAKING YOUR BLOOD PRESSURE READING 

a.  Press the START button to start off-line measurement when disconnected with iOS device. If 

connected with iOS device.your monitor can be controlled by ios device 

b.  A beep is heard and all display characters are shown for self-test. See picture 6. Please contact 

the service center if segment is missing. 

       

       

 

                                       

 Picture 6            Picture 6-1         Picture 6-2 

c.  Then the current memory bank (U1 or U2) is blinking. See picture 6-1. Press “MEM” button to 

change over to other bank. See picture 6-2. Confirm your selection by pressing “START” button. 
The current bank can also be confirmed automatically after 5 seconds with no operation. 

d.  After selecting the memory bank, the monitor starts to seek zero pressure. See picture 6-3. 
 

       

       

 

     Picture 6-3

               

Picture 6-4          Picture 6-5 

e.  The monitor inflates the cuff until sufficient pressure has built up for a measurement. Then the 

monitor slowly releases air from the cuff and carries out the measurement. Finally the blood 
pressure and pulse rate will be calculated and displayed on the LCD screen separately. Irregular 
heartbeat symbol (if any) will blink. See picture 6-4&6-5. The result will be automatically stored in 
the current memory bank. 

f.  After measurement, the monitor will turn off automatically after 1 minute of no operation. 

Alternatively, you can press the “START” button to turn off the monitor manually or control your 
monitor to test again by your app. 

g.  During measurement, you can press the “START” button to turn off the monitor manually. 

 

Note: Please consult a health care professional for interpretation of pressure measurements. 

   

 

Summary of Contents for KD-557BT


















Reviews:

No comments