IGM LAGUNA Revo 1836, Operating Instructions Manual

Page: 4 / 20

-4- www.igmtools.com
Tail stock viewed from the front
Pic. 7
Tool rest
The tool rest can be moved to any position on
the lathe bed and locked to suit the job at hand.
The tool rest has a tall profile to allow the bowl
turner to turn steep angles. The leading edge
is made from 6 mm hardened steel.
Tool rest assembled to the bed
Pic. 8
Tool rest
Pic. 9
Electrical system
220V: The electrical control system (VFD) is
housed at the back of the head stock, The VFD
converts single phase 220v to three phase.
There is a speed readout at the front of the
lathe with controls to fine adjust the rpm of
the spindle. A power cord with 220V plug is
provided.
Tail stock travel 115 mm
Tail stock removal Self-ejecting
Tail stock taper MK2
Faceplate 76 mm
Bed material Steel
Weight (net/ship) 194 kg / 206 kg
3.3 Noise emissions
Equivalent A-weighted Sound pressure level
according to EN ISO 3746: 75.66 dB(A).
Uncertainty, K in decibels: 4.0 dB (A) according
to EN ISO 4871 The figure quoted is emission
levels and are not necessarily safe working
levels. Whilst there is a correlation between the
emission and exposure levels, this cannot be
used reliably to determine whether or not further
precautions are required. Factors that influence
the actual level of exposure of the workforce
include characteristics of the work room, the
other sources of noise, etc. i.e. the number of
machines and other adjacent processes. Also
the permissible exposure level can vary from
country to country, This information, however,
will enable the user of the machine to make a
better evaluation of the hazard and risk.
Pic. 13
4. General safety
“WARNING“: For Your Own Safety Read
Instruction Manual before Operating Lathe
4.1 Safety Rules
(a) Wear eye protection.
(b) Do not wear gloves, a necktie, or loose
clothing.
(c) Tighten all locks before operating.
(d) Rotate work piece by hand before applying
power.
(e) Rough out work piece before installing on
faceplate.
(f) Do not mount split work piece or one
containing a knot.
(g) Use lowest speed when starting new work
piece.
• Keep guards in place and in working order.
• Remove adjusting keys and wrenches. Form
habit of checking to see that keys and adjusting
wrenches are removed from tool before turning
it on.
• Keep work area clean. Cluttered areas and
benches invite accidents.
• Don‘t use in a dangerous environment. Don‘t
use power tools in damp or wet locations, or
expose them to rain. Keep work area well
lighted.
VFD with cover open
Pic. 10
Power cord
Pic. 11
Tool storage
A tool storage bracket which can be mounted
on either leg.
Tool storage bracket
Pic. 12
3.2 Technical data
Motor Induction, 1420 rpm, 1,5 kW, S1
Voltage 230V, 50 Hz, 1 Ph.
3 phase output
Recommended breaker size 16 A, tripping
characteristic C (16/1/C).
Swing over bed 457 mm
Swing over banjo 343 mm
Outboard swing max. 813 mm
Distance between centres 914 mm
Floor to spindle centre 1054 mm
Floor to bed height 826 mm
Dim. W x D x H 1524 x 660 x 1194 mm
Tool rest 305 mm
Speed range high: 135 – 3500 rpm
Speed range low: 50 – 1300 rpm
VFD Delta
Spindle M33 x 3.5 mm, righthanded
Spindle taper MK 2
Spindle lock Spring loaded
Spindle indexing 14 / 36 / 48 with lock
Head stock and tail stock bore 9,5 mm